Carrier Aquazone 50PCD Скачать руководство пользователя страница 22

Страница: 22 / 48

HOT GAS REHEAT CONTROL — Units with hot gas re-

heat (HGRH) will include an additional H terminal on the im-

put terminal board for dehumidification control. To enable a

call for dehumidification, a 24V signal must be sent to the H

terminal with no voltage applied to the Y1 or O terminals. Any

call for cooling (Y1 and O) will override the dehumidification

call.

Unit heat pumps are supplied with a 50 VA control trans-

former as standard. Models with WSHP Open, Deluxe D con-

trol package, hot gas reheat (HGRH), or waterside economizer

options are supplied with a 75VA transformer. The VA ca-

pacity of the transformer should be considered when connect-

ing low voltage accessories to the heat pump such as thermo-

stats or solenoid valves. Table shows the VA draw of factory-

mounted components in the low voltage heat pump. The total

VA draw of the heat pump internal components plus any at-

tached accessories must be lower than the VA capacity of the

unit control transformer.

Step 9 — Wire Field Controls

SAFETY DEVICES AND UNIT PROTECTION MOD-

ULE (UPM) — Each unit is factory provided with a UPM

board that controls the compressor operation and monitors the

safety. See Fig. 20.

If the unit is being connected to a thermostat with a mal-

function light, this connection is made at the unit malfunction

output or relay. See Table 9 for UPM board fault blink codes.

Fig. 20 — Unit Protection Module (UPM)

Table 8 — Low Voltage VA Draw

IMPORTANT: Exceptionally long runs of thermostat wire

should be avoided to prevent voltage drops in the control

circuit.

CAUTION

Exceeding the transformer capacity can result in low con-

trol voltage, erratic unit operation or damage to the heat

pump.

WARNING

To avoid possible injury or death due to electrical shock,

open the power supply disconnect switch and secure it in

an open position during installation.

Board Power Indicator

UPM Status LED Indicator

Water Coil Freeze Protection Temperature Selection [R30]

Air Coil Freeze Protection Temperature Selection

UPM Settings

Water Coil Freeze Connection

Air Coil Freeze Connection

LED Status-Diagnostic Connection

24VAC Power Input

Compressor Contact Output

High Pressure Switch Connection

Call for Compressor Y1

Low Pressure Switch Connection

24VAC Power Common

Condensate Overflow Sensor

Dry Contact

UPM Ground Standoff

STANDARD CONSTRUCTION

HOT GAS REHEAT OR ECONOMIZER

OPTIONAL COMPONENTS

Component

Blower Relay (PSC

motors only)

6-7

Total from ‘Standard’

22-26

Monitor Relay (VA draw

per relay)

6-7

Reversing Valve

Solenoid

8-9

Additional Control

Relays

12-14

Internal 2 Way

Motorized Valve

Compressor Contactor

6-8

Hot Gas Reheat

Solenoid

8-9

Complete C board

—

Total VA draw

22-26

Total VA draw

42-49

Содержание Aquazone 50PCD

















































Результаты поиска

Содержание Aquazone 50PCD

Отзывы:

Бренды по названию

Популярные бренды

Carrier Aquazone 50PCD, Инструкция по установке, запуску и обслуживанию

Результаты поиска

Содержание Aquazone 50PCD

Отзывы:

Бренды по названию

Популярные бренды