Carrier AquaSnap 30MPA050, Руководство по установке

Страница: 21 / 44

21
Unit Mounting Requirements —
The mounting hole
weights from Fig. 18 should be used for calculating weights for
units connected via common water manifold piping (multi-
chiller applications) and using the Vibration Isolator Springs
Accessory Kit.
Multiple chiller applications using the Vibration Isolator
Springs Accessory Kit should be set on a mounting frame,
which should then be installed on the isolator springs. I-
beam or square metal tubing are acceptable materials for the
mounting frame. Each chiller MUST be supported in the
center (under the heat exchangers) by the mounting frame;
however, isolators are only necessary at the four corners of
each unit. Use Fig. 18 for the corner weights of each when
supported in four locations.
For standalone units (chillers which are not connected via
common water piping), 30MP 016-045 must be supported at
the four corner locations shown in Fig. 18. 30MP 050-071
must be supported at the six locations shown in Fig. 19.
Fig. 1 8 — Mounting Hole Weight Distribution (At Four Locations)
ESTIMATED WEIGHT DISTRIBUTION AT EACH MOUNTING HOLE — l b
UNIT 30MP
MOUNTING HOLE (lb)
A B C D
A020 252 125 226 99
A030 258 139 239 119
A040 315 183 281 149
A045 320 196 293 169
A050 391 348 351 308
A055 396 352 355 310
A060 398 358 361 320
A065 409 365 369 325
A071 416 374 379 337
W016 202 115 221 133
W020 243 142 253 152
W030 313 187 309 183
W032 305 180 304 179
W040 393 237 370 214
W045 413 256 393 235
W050 484 398 403 317
W055 490 402 407 319
W060 508 424 416 332
W065 519 432 424 337
W071 516 432 427 344
UNIT 30MP
WITH
MANIFOLD
MOUNTING HOLE (lb)
A B C D
A020 258 326 134 202
A030 266 339 148 220
A040 324 381 192 249
A045 331 394 204 267
A050 445 444 364 363
A055 451 448 368 365
A060 453 453 374 375
A065 463 461 382 380
A071 471 470 392 391
W016 312 323 230 242
W020 353 351 262 260
W030 423 395 319 291
W032 415 389 313 287
W040 502 446 379 323
W045 523 464 402 344
W050 594 505 514 425
W055 599 509 517 427
W060 618 532 527 441
W065 629 539 535 445
W071 626 540 538 452
ESTIMATED WEIGHT DISTRIBUTION AT EACH MOUNTING HOLE — kg
UNIT 30MP
MOUNTING HOLE (kg)
A B C D
A020 114 57 102 45
A030 117 63 108 54
A040 143 83 127 67
A045 145 89 133 76
A050 177 158 159 140
A055 179 159 161 141
A060 180 162 163 145
A065 185 166 167 147
A071 189 169 172 153
W016 92 52 100 60
W020 110 65 114 69
W030 142 85 140 83
W032 138 82 138 81
W040 178 108 167 97
W045 187 116 178 107
W050 219 180 183 143
W055 222 182 184 144
W060 230 192 189 150
W065 235 196 192 152
W071 234 196 193 156
UNIT 30MP
WITH
MANIFOLD
MOUNTING HOLE (kg)
A B C D
A020 117 148 61 91
A030 121 153 67 100
A040 147 173 87 113
A045 150 178 93 121
A050 202 201 165 164
A055 204 203 167 165
A060 205 205 169 170
A065 210 209 173 172
A071 213 213 178 177
W016 141 146 104 109
W020 160 159 119 118
W030 192 179 144 132
W032 188 176 142 130
W040 228 202 172 146
W045 237 210 182 156
W050 269 229 233 192
W055 272 231 234 193
W060 280 241 239 200
W065 285 244 242 202
W071 283 245 244 205
A
B C
D
CONTROL PANEL SIDE