Carrier AGAGC9PNS01B Скачать руководство пользователя страница 16

Страница: 16 / 16

A Carrier Company

Edition Date: 05/20

Catalog No:AG-KC019SPN-02

Replaces:AG-KC019SPN-01

AGAGC9PNS01B Gas Conversion Kit, Propane to Natural: Installation Instructions

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

LABEL APPLICATION

1. Fill in Conversion Responsibility Label 346162-205 and apply to

Blower Access Door of furnace. Date, name, and address of

organization making this conversion are required, see

Fig. 26

2. Attach Conversion Rating Plate Label 346162-201, -204, -206,

-207, -208 or -209 to outer door of furnace, see

Fig. 5

Fig. 6

Fig. 7

3. Attach Gas Control Conversion Label 346162-202 to gas valve. Do

not use 346162-203, which is similar.

CHECKOUT

1. Observe unit operation through two complete heating cycles.
2. See Sequence of Operation in furnace Installation, Start-Up, and

Operating Instructions.

3. Set room thermostat to desired temperature.

A200244

Fig. 26 – Gas Conversion Responsibility Label

A200245

Fig. 27 – Gas Control Conversion Label

Содержание AGAGC9PNS01B

















Результаты поиска

Содержание AGAGC9PNS01B

Отзывы:

Carrier AGAGC9PNS01B, Руководство по установке, Страница: 16 / 16

Результаты поиска

Содержание AGAGC9PNS01B

Отзывы: