Carrier 69NT40-551-500 Скачать руководство пользователя страница 51

Страница: 51 / 121

3--24

T-334

Table 3--7 Controller Pre-Trip Test Codes (Sheet 1 of 4)

Code

No.

TITLE

DESCRIPTION

NOTE

“Auto” or “Auto1” menu includes the: P0, P1, P2, P3, P4, P5, P6 and rSLts. “Auto2” menu in-

cludes P0, P1, P2, P3, P4, P5, P6, P7, P8, P9, P10 and rSLts. “Auto3” menu includes P0, P1,

P2, P3, P4, P5, P6, P7 and P8.

P0-0 Pre-Trip Initiated

All lights and display segments will be energized for five seconds at the start of

the pre-trip. Since the unit cannot recognize lights and display failures, there are

no test codes or results associated with this phase of pre-trip.

P1-0 Heaters Turned On

etup:

Heater must start in the OFF condition, and then be turned on. A current

draw test is done after 15 seconds.

Pass/Fail Criteria:

Passes if current draw change is within the range specified.

P1-1 Heaters Turned Off

Setup:

Heater must start in the ON condition, and then be turned off. A current

draw test is done after 10 seconds.

Pass/Fail Criteria:

Passes if current draw change is within the range specified.

P2-0 Condenser Fan On

Requirements:

Water pressure switch or condenser fan switch input must be

closed.

Setup:

Condenser fan is turned ON, a current draw test is done after

15 seconds.

Pass/Fail Criteria:

Passes if current draw change is within the range specified.

P2-1 Condenser Fan Off

Setup:

Condenser fan is turned OFF, a current draw test is done after

10 seconds.

Pass/Fail Criteria:

Passes if current draw change is within the range specified.

Low Speed

Evaporator Fans

equirements:

The unit must be equipped with a low speed evaporator fan, as

determined by the Evaporator Fan speed select configuration variable.

NOTE

If the unit is configured for single evaporator fan operation, Pre-Trip tests

P3-0, P3-1, P4-0 and P4-1 will fail immediately if Controller alarm codes

AL11 or AL12 are active at the start of testing.

P3-0

Low Speed

Evaporator Fan

Motors On

Setup:

The High Speed Evaporator fans will be turned on for 10 seconds, then

off for two seconds, then the low speed evaporator fans are turned on. A current

draw test is done after 60 seconds.

Pass/Fail Criteria:

Passes if change in current draw is within the range speci-

fied. Fails if AL11 or AL12 activates during test for units operating with single fan

only.

P3-1

Low Speed

Evaporator Fan

Motors Off

Setup:

The Low Speed Evaporator fan is turned off, a current draw test is done

after 10 seconds.

Pass/Fail Criteria:

Passes if change in current draw is within the range speci-

fied. Fails if AL11 or AL12 activates during test for units operating with single fan

only.

Downloaded from

ManualsNet.com

search engine

Содержание 69NT40-551-500


























































































































Результаты поиска

Содержание 69NT40-551-500

Отзывы:

Бренды по названию

Популярные бренды

Carrier 69NT40-551-500, Операция и обслуживание

Результаты поиска

Содержание 69NT40-551-500

Отзывы:

Бренды по названию

Популярные бренды