background image

T-316

7–32

b. Installation:

Install the module by reversing the removal steps.

Torque values for mounting screws (item 2, see 

Figure 7.24

) are 0.23 mkg (20 inch-pounds). Torque value for the

connectors is 0.12 mkg (10 inch-pounds).

7.20.5

Battery Replacement

If required, use tool 07-00418-00.

7.21 TEMPERATURE SENSOR SERVICE

Procedures for service of the Return Recorder, Return Temperature, Supply Recorder, Supply Temperature, Ambi-
ent, Defrost Temperature, Compressor Discharge and Compressor Suction temperature sensors are provided in
the following sub-paragraphs. 

7.21.1

Sensor Checkout Procedure

To check a sensor reading, do the following:

a. Remove the sensor and place in a 0°C (32°F) ice-water bath. The ice-water bath is prepared by filling an

insulated container (of sufficient size to completely immerse bulb) with ice cubes or chipped ice, then filling
voids between ice with water and agitating until mixture reaches 0°C (32°F) measured on a laboratory ther-
mometer.

b. Start unit and check sensor reading on the control panel. The reading should be 0°C (32°F). If the reading is

correct, reinstall sensor; if it is not, continue with the following.

c. Turn unit OFF and disconnect power supply.

d. Refer to 

Section 7.20

 and remove controller to gain access to the sensor plugs.

e. Using the plug connector marked “EC”, that is connected to the back of the controller, locate the sensor

wires (RRS, RTS, SRS, STS, AMBS, DTS, CPDS, OR CPSS as required). Follow those wires to the con-
nector and using the pins of the plug, measure the resistance. Values are provided in 

Table 7–1

.

Due to the variations and inaccuracies in ohmmeters, thermometers or other test equipment, a reading within 2%
of the chart value would indicate a good sensor. If a sensor is defective, the resistance reading will usually be much
higher or lower than the resistance values given.

7.21.2

Sensor Replacement

a. Turn unit power OFF and disconnect power supply.

b. For two wire sensors, cut cable 5 cm (2 inches) from shoulder of defective sensor and discard the defective

sensor only. For three wire sensors cut at 23 cm (9 inches). Slide the cap and grommet off well mounted
sensor and save for possible reuse. 

Do not cut the grommet.

c. If required, prepare the replacement sensor by cut ting sensor wire(s) back 40 mm (1-1/2 inch). For three

wire sensors the black wire should be cut at the middle length and the red/white wire cut to the shorter
length. (See 

Figure 7.25

)

Table 7–1 Sensor Temperature/Resistance Chart 

Temperature (C)

Temperature (F)

Resistance (Ohms)

RRS, RTS, SRS and STS:

0

32

32,650 

91

25

77

10,000

 +

 50

AMBS and DTS

0

32

32,650 + 1720 
             - 1620

25

77

10,000 + 450
             - 430

Содержание 69NT40-541-001





























































































































































Отзывы: