Carrier 50KC04 Скачать руководство пользователя страница 42

Страница: 42 / 52

Smoke Detectors

Smoke detectors are available as factory-installed options on

50KC models. Smoke detectors may be specified for supply-air

only or for return-air without or with economizer, or in combina

tion of supply-air and return-air. All components necessary for op

eration are factory-provided and mounted. The unit is factory-con

figured for immediate smoke detector shutdown operation; addi

tional wiring or modifications to unit terminal board may be

necessary to complete the unit and smoke detector configuration

to meet project requirements.

Units equipped with factory-optional return-air smoke detectors

require a relocation of the sensor module at unit installation. See

Fig. 56 for the as-shipped location.

Fig. 56 — Return Air Smoke Detector, Shipping

Position

Completing Installation of Return Air Smoke Sensor:

1. Unscrew the two screws holding the return-air smoke detec

tor assembly. See Fig. 57, Step 1. Save the screws.

2. Turn the assembly 90 degrees and then rotate end to end.

Make sure that the elbow fitting is pointing down. See

Fig. 57, Step 2.

3. Screw the sensor and detector plate into its operating position

using screws from Step 1. See Fig. 57, Step 3.

4. Connect the flexible tube on the sampling inlet to the sam

pling tube on the basepan.

ADDITIONAL APPLICATION DATA
Refer to the application data document “Factory Installed Smoke

Detectors for Small and Medium Rooftop Units 2 to 25 Tons” for

discussions on additional control features of these smoke detectors

including multiple unit coordination.

PremierLink™ Controller (Factory Option)

For details on operating 50KC-*04-06 units equipped with the

factory-installed PremierLink controller option, refer to the Pre

mierLink Retrofit Rooftop Controller Version 3.x Installation,

Start-Up, and Configuration Instructions manual.

RTU Open Controller (Factory-installed Option)

For details on operating 50KC*04-06 units equipped with the fac

tory-installed RTU Open controller refer to the

“Factory-Installed

RTU Open Multi-Protocol Controller Control, Start-Up, Opera

tion and Troubleshooting”

manual.

Controller Options

LOW AMBIENT
If the unit comes with Electro-Mechanical (EM) control, then no

adjustment is necessary.

If the unit comes with the PremierLink™ or RTU Open control

option, then refer to its installation control manual for details on

adjusting “Cooling Lock-Out” setting and configure for the spe

cific job requirements.

Fig. 57 — Completing Installation of Return Air Smoke Sensor

RETURN AIR

SMOKE DETECTOR

(AS SHIPPED)

TEP 1

TEP 2

TEP

Содержание 50KC04





















































Результаты поиска

Содержание 50KC04

Отзывы:

Carrier 50KC04, Руководство по установке, Страница: 42 / 52

Результаты поиска

Содержание 50KC04

Отзывы: