Carrier 50HCQD07 Скачать руководство пользователя

Страница: 16 / 52

Fig. 21 — Power Wiring Connections

ALL UNITS
All field wiring must comply with NEC and all local codes.

Size wire based on MCA (Minimum Circuit Amps) on the unit

informative plate. See Fig. 21 and the unit label diagram for

power wiring connections to the unit power terminal blocks

and equipment ground. Maximum wire size is #2ga AWG

(copper only) per pole.
Provide a ground fault and short circuit over-current protection

device (fuse or breaker) per NEC Article 440 (or local codes).

Refer to unit informative data plate for MOCP (Maximum

Over-Current Protection) device size.
All field wiring must comply with the NEC and local requirements.
All units except 208/230v units are factory wired for the volt-

age shown on the nameplate.

If the 208/230v unit is to be con-

nected to a 208v power supply, the control transformer must be

rewired by removing the black wire with the

-in. female

spade connector from the 230v connection and moving it to the

200v

-in. male terminal on the primary side of the transform-

er. Refer to unit label diagram for additional information.

Field power wires will be connected at line-side pressure lugs

on the power terminal block or at factory-installed option non-

fused disconnect.

NOTE: Check all factory and field electrical connections for

tightness.

Voltage to compressor terminals during operation must be

within voltage range indicated on unit nameplate. On 3-phase

units, voltages between phases must be balanced within 2%

and the current within 10%. Use the formula shown in the ex-

ample below to determine the percent of voltage imbalance.

Operation on improper line voltage or excessive phase imbal-

ance constitutes abuse and may cause damage to electrical

components. Such operation would invalidate any applicable

Carrier warranty.
NOTE: Check all factory and field electrical connections for tight-

ness.

CONVENIENCE OUTLETS

Two types of convenience outlets are offered on 50HCQ mod-

els: non-powered and unit-powered. Both types provide a 125-

volt GFCI (ground-fault circuit interrupter) duplex receptacle

rated at 15A behind a hinged waterproof access cover, located

on the end panel of the unit. See Fig. 22.

Fig. 22 — Convenience Outlet Location

Installing Weatherproof Cover

A weatherproof while-in-use cover for the factory-installed

convenience outlets is now required by UL standards. This

cover cannot be factory-mounted due its depth; it must be in-

stalled at unit installation. For shipment, the convenience outlet

is covered with a blank cover plate.
The weatherproof cover kit is shipped in the unit’s control box.

The kit includes the hinged cover, a backing plate, and gasket.

1. Remove the blank cover plate at the convenience outlet;

discard the blank cover.

2. Loosen the two screws at the GFCI duplex outlet, until

approximately

1/2

in. (13 mm) under screw heads is

exposed. Press the gasket over the screw heads.

3. Slip the backing plate over the screw heads at the keyhole

slots and align with the gasket; tighten the two screws

until snug (do not over-tighten).

4. Mount the weatherproof cover to the backing plate as

shown in Fig. 23.

Units Without Disconnect Option

Units With Disconnect Option

Optional

Disconnect

Switch

Disconnect factory test leads; discard.

Factory

Wiring

IFC

(3 Phase

Indoor Motor)

(1 Phase Indoor Motor

and 3 Phase Unit)

208/230-3-60

460-3-60
575-3-60

Disconnect

per

NEC

208/230-1-60

Disconnect

per

NEC

WARNING

ELECTRICAL OPERATION HAZARD
Failure to follow this warning could result in personal

injury or death.
Units with convenience outlet circuits may use multiple

disconnects. Check convenience outlet for power status

before opening unit for service. Locate its disconnect

switch, if appropriate, and open it. Lock-out and tag-out

this switch, if necessary.

WARNING

Failure to follow this warning could result in personal

injury or death.
Disconnect all power to unit and convenience outlet.

Lock-out and tag-out all power.

CONVENIENCE

OUTLET GFCI

PWD-CO FU

WITCH

PWD-CO TRAN

FORMER

CONTROL BOX
ACCE

PANEL

Содержание 50HCQD07





















































Результаты поиска

Содержание 50HCQD07

Отзывы:

Похожие инструкции для 50HCQD07

Бренды по названию

Популярные бренды

Carrier 50HCQD07, Руководство по установке

Результаты поиска

Содержание 50HCQD07

Отзывы:

Похожие инструкции для 50HCQD07

Бренды по названию

Популярные бренды