Carrier 50HCQ07 Скачать руководство пользователя

Страница: 35 / 52

To use the keypad when working with Setpoints, System and

Advanced Settings, Checkout tests and Alarms:
1. Navigate to the desired menu.
2. Press the

(Enter) button to display the first item in the

currently displayed menu.

3. Use the

▲

and

▼

buttons to scroll to the desired parame-

ter.

4. Press the

(Enter) button to display the value of the

currently displayed item.

5. Press the

▲

button to increase (change) the displayed

parameter value.

6. Press the

▼

button to decrease (change) the displayed

parameter value.

NOTE: When values are displayed, pressing and holding the

▲

▼

button causes the display to automatically increment or decre-

ment.
1. Press the

(Enter) button to accept the displayed value

and store it in nonvolatile RAM. “CHANGE STORED”
displays.

2. Press the

(Enter) button to return to the current menu

parameter.

3. Press the (Menu Up/Exit) button to return to the previ-

ous menu.

Menu Structure
Table 10 illustrates the complete hierarchy of menus and pa-

rameters for the EconoMi$er

X system.

The Menus in display order are:
• STATUS

• SETPOINTS

• SYSTEM SETUP

• ADVANCED SETUP

• CHECKOUT

• ALARMS

NOTE: Some parameters in the menus use the letters MA or

MAT, indicating a mixed air temperature sensor location before

the cooling coil. This unit application has the control sensor locat-

ed after the cooling coil, in the fan section, where it is designated

as (Cooling) Supply Air Temperature or SAT sensor.

Setup and Configuration

Before being placed into service, the W7220 Economizer mod-

ule must be set up and configured for the installed system.

The setup process uses a hierarchical menu structure that is

easy to use. Press the

▲

and

▼

arrow buttons to move forward

and backward through the menus and press the

(Enter) but-

ton to select and confirm setup item changes.

Time-Out and Screensaver

When no buttons have been pressed for 10 minutes, the LCD

displays a screen saver, which cycles through the Status items.

Each Status items displays in turn and cycles to the next item

after 5 seconds.

IMPORTANT: Table 10 illustrates the complete hierar-

chy. Your menu parameters may be different depending

on your configuration.
For example if you do not have a DCV (CO

) sensor,

then none of the DCV parameters appear and only MIN

POS will display. If you have a CO

sensor, the DCV

MIN and DCV MAX will appear.

IMPORTANT: During setup, the economizer module is

live at all times.

Содержание 50HCQ07





















































Результаты поиска

Содержание 50HCQ07

Отзывы:

Похожие инструкции для 50HCQ07

Бренды по названию

Популярные бренды

Carrier 50HCQ07, Руководство по установке

Результаты поиска

Содержание 50HCQ07

Отзывы:

Похожие инструкции для 50HCQ07

Бренды по названию

Популярные бренды