40MPHB: Owner’s Manual
Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.
8
Remote Control Operation - Quick Start
NOTE: When transmitting a command from the remote control to
the unit, be sure to point the control toward the right side of
the unit. The unit confirms receipt of a command by
sounding an audible beep.
1. Turn the unit on by pushing
ON/OFF
.
NOTE: If there is a preference for °C rather than °F (default), press
and hold the
+
and
-
temperature set point buttons together
for approximately 3 seconds.
2. Select the desired mode by pushing
MODE
.
A220212
Fig. 9 —Modes
3. Select the temperature set point by pointing the control toward the
unit and pressing the increase/decrease temperature set point buttons
until the desired temperature appears on screen.
4. Press
FAN
to select the desired fan speed.
NOTE: If the unit is operating in DRY or AUTO mode, the fan speed
will be automatically set and cannot be adjusted.
Set the airflow direction. When the unit is turned on, the
Up-Down
airflow louvers default to the cooling or heating position. The user can
adjust the horizontal
Up-Down
airflow louver position by pushing
DIRECT
or have continuous louver movement by pressing
SWING
.
When the outside temperature is below 32°F (0°C), we strongly
recommend maintaining power on the unit to ensure smooth ongoing
performance.
To optimize unit performance, perform the following:
• Keep doors and windows closed
• Limit energy usage by using TIMER ON and TIMER OFF
functions.
• Do not block air inlets or outlets.
• Regularly inspect and clean air filters.
Set Function
A220035
Fig. 10 —Set Function
1. Press
SET
to enter the
FUNCTION
setting.
2. Press
SET
or
TEMP
or
TEMP
to select the desired function.
3. When the selected symbol flashes on the display, press
OK
to
confirm.
To cancel the selected function, perform the same steps.
Press
SET
to scroll through the operation functions as follows:
A220038
Fig. 11 — Functions
Breeze Away Function
(some units)
:
This feature avoids direct air flow from blowing on the room’s occupants.
NOTE: This feature is available under COOL, FAN and DRY mode
only.
Active Clean Function (some units)
:
The
Active Clean Technology
washes away dust, mold, and grease that
may cause odors when it adheres to the heat exchanger by automatically
freezing and then rapidly thawing the frost. When this function is turned
on, the indoor unit window displays “CL”, after 20 to 45 minutes, the unit
turns off automatically and cancels the
CLEAN
function.
FRESH Function (some units):
When the
FRESH
function is initiated, the Ionizer/Plasma Dust Collector
(depending on models) is energized and helps to remove pollen and
impurities from the air.
SLEEP Function
:
The
SLEEP
function is used to decrease energy use while you sleep (and
do not need the same temperature settings to remain comfortable). This
function can only be activated via remote controller. For the detail, see
SLEEP OPERATION
in the User’s Manual.
NOTE: The SLEEP function is not available in FAN or DRY mode.
FOLLOW ME Function
:
The
FOLLOW ME
function enables the remote control to measure the
temperature at its current location and sends this signal to the air
conditioner every 3 minutes. When using the
AUTO
,
COOL
or
HEAT
modes, measuring the ambient temperature from the remote controller
(instead from the indoor unit itself) allows the air conditioner to optimize
the temperature around the occupants to ensure maximum comfort.
NOTE: Press and hold BOOST for seven seconds to start/stop the
FOLLOW ME MEMORY feature.
• IF the MEMORY feature is activated, “ON” appears on the display for 3
seconds.
• If the MEMORY feature stops, “OFF” appears on the display for 3
seconds.
NOTE: When the FOLLOW ME Memory feature is activated, it will
not be canceled by pressing ON/OFF, MODE or power
failure to the indoor unit.
AP Function (some units)
:
Select the
AP
function to configure the wireless network. For some units,
it does not work by pressing
SET
. To enter the
AP
mode, continuously
press
LED
seven times for 10 seconds.
FREEZE Protection
With the unit in
HEAT
mode and the wireless remote pointed at the
indoor unit, press the down arrow until the setpoint is 60°F (16°C). Press
the down arrow two times within two seconds to activate the 46°F (8°C)
heating function (heating set back). The unit now operates at a set
temperature of 46°F (8°C). The indoor unit display shows
FP
. No icon
appears on the remote control.
NOTE: This function is only available in the heating mode.
Under this function, the unit heats at high fan speed until the space
temperature is 46°F (8°C). This mode can also be deactivated by pressing
ON/OFF
,
SLEEP
,
MODE
,
FAN
, or either
TEMP
arrow.