Carrier 39HXC Скачать руководство пользователя | Manualshive

Страница: 17 / 64

background image

3.4 - Mixing damper

If a mixing damper is present in the unit (P27 = with), it is necessary to configure its opening time (P166).
Mit den Parametern P208 und P209 kann eine Mindest-Öffnung eingestellt werden.

The damper operates with 100% fresh air in night cooling or free cooling mode. It is modulated when there is an air quality requirement.
If there is a mixing damper present and the mixing opening demand is greater than 95%, then the outdoor side isolation dampers (if

present) close.
The mixing damper can be forced to close using parameter P163 (accessible via BMS)

27

Mixing damper

163

load shedding of mixing damper

166

Mixing damper opening time

208

Mixing damper minimum setpoint 1

209

Mixing damper minimum setpoint 2

3.5 - Filter management

Pressure sensors measure the filter fouling (intake and exhaust), and a fault appears if the filter is fouled (new filter to be ordered and

replacement scheduled) or blocked (machine is shut down).

The threshold is calculated automatically according to the filter type (M5, F7, F9, M5+F7, M5+F9, F7+F9) and the air flow rate.
It is possible to view the pressure difference and thresholds for each filter (P312 to P317).

7

Intake filter type

8

Intake filter coefficient

15

Exhaust filter type

16

Exhaust filter coefficient

3.6 - Temperature control

The set temperature may be:

-

The return air temperature

-

The room temperature (if the Th-Tune room remote control is present)

-

The supply air temperature

This choice is made via parameter P154.
The temperature is set via a PID which calculates a heating requirement (P395) or a cooling requirement (P394). There is one heating

setpoint (P180) and one cooling setpoint (P170), with the option to have a deadband between these two different setpoints. The

calculated requirement is then divided between the heating or cooling elements, in the following order of priority: heat recovery unit,

hydraulic coils, electric heater.

Heating requirement (%)

P182 Proportional band

Heating

setpoint

Setpoint 1: P180

Setpoint 2: P181

Setpoint 1: P170

Setpoint 2: P171

Room temperature

Return air temperature

Supply air temperature

Cooling

setpoint

Cooling requirement (%)

P172 Proportional band

-

The heating and cooling setpoints must not overlap in automatic mode (P155)

-

In heating only or cooling only mode, the setpoints may overlap.

154

Target temperature selection

155

Temperature control mode selection

168

Heating or cooling change authorisation time delay

Cooling PID

170

Temperature setpoint 1 in cooling mode

171

Temperature setpoint 2 in cooling mode

172

Temperature control PID proportional band (P) in cooling mode

173

Temperature control PID integral time (I) in cooling mode

174

Temperature control PID derivative time (D) in cooling mode

3 - FEATURES

17

«
...
15
16
17
18
19
...
»

Содержание 39HXC

































































Отзывы:

Нет отзывов

Похожие инструкции для 39HXC

Бренд: Panasonic Страницы: 56

Бренд: Panasonic Страницы: 60

Бренд: Panasonic Страницы: 297

PrecisionAir WS

Бренд: Dantherm Cooling Страницы: 19

Бренд: German pool Страницы: 28

MinusA2 SPA-780N

Бренд: Rabbit Air Страницы: 2

Air Purification System Pureair

Бренд: Lennox Страницы: 6

Бренд: mabe Страницы: 12

Бренд: Bard Страницы: 137

Бренд: SAIKO Страницы: 16

Бренд: Zibro Страницы: 86

Бренд: ICP Страницы: 2

Бренд: Winix Страницы: 12

climaVAIR V 7-025 NW

Бренд: Vaillant Страницы: 26

Бренд: Eurapo Страницы: 88

bycool SPLIT OFF ROAD

Бренд: dirna Bergstrom Страницы: 56

Бренд: UFESA Страницы: 36

Бренд: Daikin Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды