Fig. 2—38BRC060 208/230v, 1 Phase, 60 Hertz
A98017
CH (NOTE #9)
RED or BLK
BLK
208/230 1Ø
POWER
SUPPLY
L1
L2
EQUIP
GND
CONT
11 21
13 23
YEL
OFM
YEL
COMP BLU
BRN
BRN
YEL
S
C
R
YEL
YEL
BLU
BLU
BRN
*SC
BLK
BLK
*ST
*SR
1 2
5
CAP
*LPS
*DTS
*HPS
BLK
BLK
YE
L
BLU
VIO
H
C
F
CONNECTION DIAGRAM
+t
°
BLU
BLK
BLU
YE
L
*CTD
BRN
(NOTE #14)
BLU
BLU
BLK
*LLS
BLK
Y
R
G
INDOOR THERMOSTAT (NOTE #5)
INDOOR BLOWER MOTOR
EXTERNAL POWER
SUPPLY 24V
(NOTES #3 & #6)
(NOTE #8)
FACTORY POWER WIRING
FACTORY CONTROL WIRING
FIELD CONTROL WIRING
FIELD POWER WIRING
COMPONENT CONNECTION
FIELD SPLICE
JUNCTION
CONT CONTACTOR
CAP
CAPACITOR (DUAL RUN)
*CH
CRANKCASE HEATER
*CHS
CRANKCASE HEATER SWITCH
COMP COMPRESSOR
*CTD
COMPRESSOR TIME DELAY
*DTS
DISCHARGE TEMP. SWITCH
*HPS
HIGH PRESSURE SWITCH
IFR
INDOOR FAN RELAY
*LLS
LIQ. LINE SOLENOID VALVE
*LPS
LOW PRESSURE SWITCH
OFM
OUTDOOR FAN MOTOR
*SC
START CAPACITOR
*SR
START RELAY
*ST
START THERMISTOR
* MAY BE FACTORY OR FIELD
INSTALLED.
-LEGEND-
SCHEMATIC DIAGRAM
(LADDER FORM)
11
21
CONT
L1
QUIP
GND
*SR
*SC
5
2
1
H
C
F
*ST
OFM
+t
°
CONT
23
13
CAP
S
C
R
COMP
L2
*LPS
*DTS
*HPS
CONT
IFR
EXTERNAL POWER SUPPLY 24 V
*CTD
(NOTE #14)
Y
G
R
OOR THERMOSTAT
R C
*CH
-NOTES-
1. Symbols are electrical representation only.
2. Compressor and fan motor furnished with inherent thermal
protection.
3. To be wired in accordance with National Electric N.E.C.
and local codes.
4. N.E.C. class 2, 24 V circuit, min. 40 VA required, 60 VA on
units installed with LLS.
5. Use copper conductors only.
6. Connection for typical cooling only thermostat, for other
arrangements, see installation instructions.
7. If indoor section has a transformer with a grounded
secondary, connect the grounded side to the BRN lead.
8. When start relay and start capacitor are installed, start
thermistor is not used.
9. CH not used on all units.
10.If any of the original wire, as supplied, must be replaced,
use the same or equivalent wire.
11.Check all electrical connections inside control box for
tightness.
12.Do not attempt to operate unit until service valves have
been opened.
13.Do not rapid cycle compressor. Compressor must be off
3 minutes to allow pressures to equalize between high
and low side before starting.
14.Wire not present if HPS, LPS, DTS or CTD are used.
15.Use conductors suitable for at least 75
°
C (167
°
F).
324474-101 REV. A
. Compressor damage may occur if system is over charged.
. This unit is factory charged with R-22 in accordance with the amount shown on the rating plate. The charge is
adequate for most systems using matched coils and tubing not over 15 feet long. The best performance will be
achieved when the unit operates with a suction gas superheat at the compressor inlet of 5
°
F at normal rating
conditions of the air conditioning and refrigeration institute (ARI). This chart may be used to approximate the
charge if ARI rating conditions cannot be obtained. ARI rating conditions are equivalent to DOE test "A"
conditions. See product data literature for required indoor air flow rates and for use of line lengths over 15 Ft.
. Carefully relieve refrigerant pressure within this unit before final disposal.
CAUTION
LOGIC
T1
T3
T2
IFR
C
R
*LLS
LOGIC
T1
T3
T2
*CHS
RED or BLK
BLK
*CHS
2
