manualshive.com logo in svg

Carrier 300, Руководство по эксплуатации и обслуживанию, Страница: 2 / 54

Поделиться
Скачать
Carrier 300 Скачать руководство пользователя страница 2

Operation & Service Manual

 

 

 

 

 
 

Carrier Transicold Europe 

31/03/07 

Viento - Installation/Rev- #2/54 

 

Introduction...................................................................................................................................................................................4

 

Preparation before installation ....................................................................................................................................................5

 

Vehicle partition .......................................................................................................................................................................................................... 6

 

Box preparation ............................................................................................................................................................................7

 

Drilling......................................................................................................................................................................................................................... 7

 

Roof top and cut mounting............................................................................................................................................................................................................8

 

Nosemount..................................................................................................................................................................................................................................11

 

Evaporator ..................................................................................................................................................................................................................................12

 

Harness and hoses hole .............................................................................................................................................................................................................14

 

Drain water hose hole .................................................................................................................................................................................................................15

 

Mushrooms ............................................................................................................................................................................................................... 16

 

Preparation .................................................................................................................................................................................................................................16

 

Set up..........................................................................................................................................................................................................................................18

 

Unit installation...........................................................................................................................................................................19

 

Evaporator installation ...............................................................................................................................................................22

 

Hoses ...........................................................................................................................................................................................23

 

Mounting recommendations...................................................................................................................................................................................... 24

 

Preparation ............................................................................................................................................................................................................... 25

 

Unit connection...........................................................................................................................................................................27

 

Refrigeration hoses................................................................................................................................................................................................... 29

 

Evaporator connection...............................................................................................................................................................33

 

Refrigeration hoses................................................................................................................................................................................................... 33

 

RAT sensor............................................................................................................................................................................................................... 35

 

Drain pan .................................................................................................................................................................................................................. 36

 

INSTALLATION

Table of content 

Содержание 300























































Отзывы:

Нет отзывов