manualshive.com logo in svg

Carotron Elite Pro EPN020-000, Инструкция по эксплуатации

Carotron Elite Pro EPN020-000 - профессиональное устройство для управления приводом. Инструкция по эксплуатации доступна для загрузки бесплатно на manualshive.com. Получите подробное руководство по установке и использованию этого продукта, чтобы оптимизировать работу вашей системы управления.

Поделиться
Скачать
background image

 
 

23 

Jog Delay (246) 
This adjustment serves to extend the mechanical life of the armature contactor by reducing 
the number of mechanical operations in an application where a high rate of repeat "jogging" is 
performed. When the Jog button is pressed and then released, the reference is immediately 
clamped to stop the motor but the contactor is held energized for up to ten seconds. Pressing 
the Jog button again within this "delay" period will cause the motor to immediately jog and will 
reset the delay. 

 

Run (239) 
The 

Run

 control input is used to put the drive into the run mode. Depending on the 

Logic 

Select

 parameter, this input can be either momentary or maintained. 

Digital input 1

 writes to 

this parameter in the factory preset configuration.

 Drive Ready

 must be True for this input to 

operate. 

 

Stop (240) 
The 

Stop

 control input is used to stop the drive when 

Logic Select

 is set for 3 Wire 

(momentary) mode. The manner in which the drive is stopped is controlled by the 

Stop Mode

 

parameter. 

Digital input 2

 writes to this parameter in the factory preset configuration. 

 

Stop Mode (232) 
The 

Stop Mode

 parameter selects between 3 type of stopping methods. The Ramp Stop 

selection will stop the drive using the Accel/Decel rates. Quick Stop provides a rapid current-
limit stop. The Coast Stop selection clamps all the loops, and allows the motor to coast to 
stop. Stopping time will be determined by the inertia, friction, and loading characteristics. 
 
Jog (241) 
The 

Jog

 control input is used to run the drive while the Jog button is pressed. The Jog 

Reference is selected instead of References 0-3 in the Setpoints block. Digital input 3 writes 
to this parameter in the factory preset configuration. 

Drive Ready

 must be True for this input 

to operate. 

 

Run Status (242, Read-Only) 
The 

Run Status

 is a status output that becomes True when the drive is in the Run mode. In 

the factory preset configuration, this parameter controls 

Relay Output 2

. 

 

Jog Status (243, Read-Only) 
The 

Jog Status

 is a status output that becomes True when the drive is in the Jog mode. In 

the factory preset configuration, this parameter writes to Ramp Select in the Accel/Decel 
block. 

 

Armature Pilot (244, Read-Only) 
The 

Armature Pilot

 is a status output that becomes True when the drive is in the Run or Jog 

modes. This output is used to control the armature contactor. 

 

Drive Ready (303, Read-Only) 
The 

Drive Ready

 parameter indicates the status of the drive. If there are no latched faults 

and the 

Run Permit

 input is True, 

Drive Ready

 is True and the drive can be started. If at any 

time there is a fault or the 

Run Permit

 becomes False, 

Drive Ready

 is forced to the False 

state and the drive is shutdown. In the factory preset configuration, this parameter controls 

Relay Output 3

. 

 

Drive Status (422, Read-Only) 
The Drive Status parameter indicates the state of the Elite Pro drive. Refer to Table 7. Note 
this parameter is not directly accessible from the keypad. 

Содержание Elite Pro EPN020-000















































































































Отзывы:

Нет отзывов

Похожие инструкции для Elite Pro EPN020-000

Lamtec 662R2127 Operatoring Instructions preview
662R2127
Бренд: Lamtec Страницы: 40
elero LIMAline 60 Operating Instructions Manual preview
LIMAline 60
Бренд: elero Страницы: 31
Unimotion MTV 65 Use, Maintenance And Assembly Instructions preview
MTV 65
Бренд: Unimotion Страницы: 22
G-U ELTRAL K25 Installation And Operating Instructions Manual preview
ELTRAL K25
Бренд: G-U Страницы: 32
Sanhua VSD2001 Series Instructions preview
VSD2001 Series
Бренд: Sanhua Страницы: 5
Stober EZ Series Operating Manual preview
EZ Series
Бренд: Stober Страницы: 7
Simu T5 AUTO+SHORT Original Instructions Manual preview
T5 AUTO+SHORT
Бренд: Simu Страницы: 16
TOX PRESSOTECHNIK Powerpackage Q Series Original Operating Instructions preview
Powerpackage Q Series
Бренд: TOX PRESSOTECHNIK Страницы: 80
Melec GDB-5K50 Instruction Manual preview
GDB-5K50
Бренд: Melec Страницы: 54
Qirod QD100 Series User Manual preview
QD100 Series
Бренд: Qirod Страницы: 163
IBM 22P6959 User Manual preview
22P6959
Бренд: IBM Страницы: 50
Danfoss Vacon NXS Series Operating Manual preview
Vacon NXS Series
Бренд: Danfoss Страницы: 238
Parker Bayside Stealth Advanced PS Product Manual preview
Bayside Stealth Advanced PS
Бренд: Parker Страницы: 13
Bardac E3 Series Quick Start Manual preview
E3 Series
Бренд: Bardac Страницы: 24
NEC NE3351-134 User Manual preview
NE3351-134
Бренд: NEC Страницы: 9
Panasonic MINAS A6SG Quick Start Manual preview
MINAS A6SG
Бренд: Panasonic Страницы: 20
ABB DCS550-S01 Quick Manual preview
DCS550-S01
Бренд: ABB Страницы: 108
Yamaha CRW3200UXZ - 24x10x40 External USB 2.0 CD-RW... Owner'S Manual preview
CRW3200UXZ - 24x10x40 External USB 2.0 CD-RW...
Бренд: Yamaha Страницы: 48

Бренды по названию

Популярные бренды

Загрузить еще бренды