6-1136
2
Rev. 09/17/18
PLEASE REVIEW ALL WARNING INSTRUCTIONS PRIOR TO OPERATION. SAVE THIS MAN U AL FOR FUTURE REF ER ENCE.
FAILURE TO OBSERVE THESE WARNINGS COULD RE SULT IN IN JU RY.
WARNING
• Do not lubricate tools with
flammable or volatile liquids
such as kerosene, diesel or jet
fuel.
• Drill bits can bind suddenly
and causing rotation of the
work piece or tool, causing
injury to arms and/or
shoulders. Enough torque is
generated to cause falls. Always use
sharp bits. Use less downward pressure
at breakthrough.
• Do not force tool beyond its rated
capacity.
• RPM OF THE ACCESSORY
MUST EXCEED TOOL RPM
• Never use dull, chipped or damaged
accessories. Never cool a hot
accessory in water as brittleness
and early failure can result, Accessory
breakage or tool damage may result
from prying. Take smaller bites to
avoid getting stuck.
• Use replacement parts and accessories
recommended by NAPA.
• Servicing and repairs should only be
made by an authorized service center.
• Do not use (or modify) the tool
for any other purpose than that
for which it was designed without
consulting the manufacturer's
authorized representative.
• Do not remove any labels. Replace
damaged labels.
• Failure to heed these warnings may
result in personal injury and/or property
damage.
WARNING:
This product
can expose you to chemicals
including nickel, which is
known to the State of California
to cause cancer and birth defects
or other reproductive harm.
For more information go to
www.P65Warnings.ca.gov.
THIS INSTRUCTION MAN U AL
CON TAINS IMPORTANT
SAFETY INFORMATION.
READ THIS IN STRUC TION
MANUAL CARE FUL LY AND
UN DER STAND ALL IN FOR MA TION
BE FORE OP ER AT ING THIS TOOL.
It is the responsibility of the owner to
make sure all personnel read this manual
prior to using the device. It is also the
responsibility of the device owner to keep
this manual intact and in a convenient
location for all to see and read. If the
manual or product labels are lost or not
legible, contact NAPA for replacements.
If the operator is not fluent in English,
the product and safety instructions shall
be read and discussed with the operator
in the operator's native language by the
purchaser/owner or his designee, making
sure that the operator comprehends its
contents.
• Always operate, inspect and maintain
this tool in accordance with American
National Standards Institute Safety
Code of Portable Air Tools (ANSI
B186.1) and any other applicable
safety codes and regulations.
• For safety, top performance
and maximum durability of
parts, operate this tool at 90
psig; 6.2 bar max air pressure with 3/8"
diameter air supply hose.
• Always wear impact-resistant
eye and face protection when
operating or performing
maintenance on this tool (users and
bystanders).
• High sound levels can cause
permanent hearing loss.
Always use hearing protection
as recommended by your employer an
OSHA regulations while using this tool
(users and bystanders).
• Operators and maintenance personnel
must be physically able to handle the
bulk, weight and power of this tool.
• Keep tool out of reach of children.
• Air powered tools can vibrate
in use. Vibration, repetitive
motions or uncomfortable
positions over extended periods of time
may be harmful to your hands and arms.
Discontinue use of tool if discomfort,
tingling feeling or pain occurs. Seek
medical advice before resuming use.
• Air under pressure can cause
severe injury. Never direct air at
yourself or others. Always turn
off the air supply, drain hose of
air pressure and detach tool
from air supply before installing,
removing or adjusting any
accessory on this tool, or before
performing any maintenance on
this tool. Failure to do so could result in
injury. Whip hoses can cause serious injury.
Always check for damaged, frayed or loose
hoses and fittings, and replace immediately.
Do not use quick detach couplings at tool.
See instructions for correct set-up.
• Do not operate a damaged or worn tool.
Do not use quick-detach couplings at
tool. See instructions for correct set-up.
• Place tool on the work before starting
the tool. Do not point or indulge in any
horseplay with this tool.
• Slipping, tripping and/or falling
while operating air tools can be
a major cause of serious injury or
death. Be aware of excess hose left on the
walking or work surface.
• Keep body working stance balanced
and firm. Do not overreach when
operating the tool.
• Anticipate and be alert for sudden
changes in motion during start up and
operation of any power tool.
• Note direction of rotation BEFORE
operating this tool
• Do not carry tool by the hose.
Protect the hose from sharp
objects and heat.
• Tool shaft may continue to rotate
briefly after throttle is released.
Avoid direct contact with
accessorie during and after use. Gloves will
reduce the risk of cuts or burns
• Keep away from rotating end of
tool. Do not wear jewelry or
loose clothing. Secure long hair.
Scalping can occur if hair is not kept away
from tool and accessories. Choking can
occur if neckwear is not kept away from tool
and accessories.
• This tool is not insulated against
electric shock.
• This tool must not be used in
explosive atmospheres.
RPM
RPM
RPM
