Carlisle Binks AA1600M Скачать руководство пользователя страница 14

Страница: 14 / 14

77-2921-R12 (2/2021)

14 / 14

www.carlisleft.com

WARRANTY POLICY

This product is covered by Carlisle Fluid Technologies’ materials and workmanship limited warranty.

The use of any parts or accessories, from a source other than Carlisle Fluid Technologies,

will void all warranties. Failure to reasonably follow any maintenance guidance provided

may invalidate any warranty.

For specific warranty information please contact Carlisle Fluid Technologies.

Carlisle Fluid Technologies is a global leader in innovative finishing technologies.

Carlisle Fluid Technologies reserves the right to modify equipment specifications without prior notice.

BGK™, Binks

, DeVilbiss

, Hosco

, MS

, and Ransburg

are all registered trademarks of Carlisle Fluid Technologies, Inc.

For technical assistance or to locate an authorized distributor,

contact one of our international sales and customer support locations.

Region

Industrial/Automotive

Automotive Refinishing

Americas

Tel: 1-800-992-4657

Tel: 1-800-445-3988

Fax: 1-888-246-5732

Fax: 1-800-445-6643

Europe, Africa,

Middle East, India

Tel: +44 (0)1202 571 111

Fax: +44 (0)1202 573 488

China

Tel: +8621-3373 0108

Fax: +8621-3373 0308

Japan

Tel: +81 45 785 6421

Fax: +81 45 785 6517

Australia

Tel: +61 (0) 2 8525 7555

Fax: +61 (0) 2 8525 7575

For the latest information about our products, visit www.carlisleft.com

Содержание Binks AA1600M















Результаты поиска

Содержание Binks AA1600M

Отзывы:

Бренды по названию

Популярные бренды

Carlisle Binks AA1600M, Руководство по обслуживанию

Результаты поиска

Содержание Binks AA1600M

Отзывы:

Бренды по названию

Популярные бренды