CARL GOLDBERG 120 ARF Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 30

background image

24

7.

Attach the EZ connector to the inside hole

on the rudder arm.

Insert the nose gear steering pushrod in the

EZ connector and adjust. Tighten the set

screw on top.

Elevator Servo & Pushrod Installation

1.

Collect the following items:

(2) 4-40 x 36” pushrods
(2) 4-40 metal clevis

(2) Silicone clevis keepers

(2) 4-40 jam nut

s

2.

Insert the two 4-40 pushrods into the nylon

tubes in the fuselage. Pull them out the rear

holes and screw into the elevator horn

brackets. They should screw all the way

into the clevis.

3.

Mount the two elevator servos using the

hardware supplied with the radio. The output

arm should be forward.

4.

Install the silicone clevis keeper on the cle-

vis. Screw a 4-40 nut on the pushrod then

the clevis. Attach the clevis to the servo arm.

Center the servo with the radio and adjust

the clevis till the elevator is neutral. Tighten

the jam nut against the clevis. Don’t forget

the arm retaining screw.

THROTTLE SERVO INSTALLATION

1.

Collect the following items:

(1) 2-56 x 18” pushrod
(1) Nylon snap link

(1) EZ servo connector

«
...
22
23
24
25
26
...
»

Содержание 120 ARF































Отзывы:

Нет отзывов

Похожие инструкции для 120 ARF

Бренд: Dancing Wings Hobby Страницы: 2

Kittyhawk Mk.Ia

Бренд: Eduard Страницы: 3

Бренд: T-Motor Страницы: 2

Battleship Tirpitz

Бренд: REVELL Страницы: 30

BATTERY BUS, SETRA S 315

Бренд: Faller Страницы: 2

Бренд: Smoby Страницы: 2

Бренд: Stevens AeroModel Страницы: 27

F-16C FIGHTING FALCON 1120mm 28/2021

Бренд: Paper Replika Страницы: 3

Weaver Nickel Plate Road L1a

Бренд: Quality Craft Страницы: 6

Бренд: The Wings Maker Страницы: 13

AMAZING ANIMALS M3198

Бренд: Fisher-Price Страницы: 4

Fordhampton Farm House

Бренд: GAUGEMASTER Страницы: 4

Star Wars Electronic Ask Yoda 72410

Бренд: Hasbro Страницы: 4

Super Mario Adventures with Peach

Бренд: LEGO Страницы: 24

Бренд: PARKZONE Страницы: 24

Бренд: PIKO Страницы: 12

TWISTER CP GOLD

Бренд: J. Perkins Страницы: 16

EINSCHLAFHILFE EULE

Бренд: X4-TECH Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды