background image

6

2.

With the aileron servo door in place, make a

mark at a 90º degree angle to the trailing edge

and in line with the servo arm.

3.

Position the control horn bolt so that it is 3/4”

back from the hinge line on the mark that you

jut made.

4.

Using a 9/64" drill bit, make a hole in the

aileron through to the top side. 

HINT: Drill the hole from the bottom half way. Then

measure and mark the top of the aileron and

drill down to the hole from the top of the

aileron.

5.

Insert the 6-32 x 2” screw from the top through

the aileron.
Place the #6 washer and the 6-32 hex nut on

the bolt and tighten. Make sure that you use

thread lock on the bolt and nut.
Screw the black adjustable horn bracket on

the bolt.

6.

Thread on to each end of a 4-40 x 4” pushrod

a nut and Golden Clevis.
Mount the pushrod onto the servo and the

horn bracket.
Slide the clevis clip on to each of the Golden

Clevis pins.
Repeat the above steps for the second

aileron.

AILERON CONTROL HORN INSTALLATION

1.

Collect the following items

(2) 4-40 Golden Clevis

(2) Clevis Clips

(2) 4-40 Hex Nut

(1) 4-40 x 4" Double threaded wire

(1) 6-32 x 2” Bolt

(1) 6-32 Hex nut

(1) #6 Washer

(1) 6-32 Black Horn Bracket

6.

Using the #4 x 1/2" screw supplied with this

kit, screw the door to the mounting plate. 
Repeat the above steps for the second aileron

servo.

Содержание Sukhoi ARF




















Отзывы: