Carl Goldberg Products Sukhoi ARF Скачать руководство пользователя

Страница: 18 / 19

BOLTING ON THE WING

Gather the following items

(1) Right & Left Wing Panels
(2) 1/4-20 x 2” Nylon Bolt
(1) Wing Tube

HATCH AND CANOPY

Gather the following items

(1) Hatch
(4) 4-40 x 1/2 Socket Head Bolt
(4) #4 Washer
(1) Cockpit insert
(1) Canopy

Fit the hatch under the cowl (tight fit) and slide

it forward till the front dowel slides into the

hole in the front former. If the dowel seems

tight then drill the hole in the former out bigger.

Using the 4-40 x 1/2” bolts and washers,

mount the hatch to the top of the fuselage.

Use thread lock.

Place the cockpit insert over the hatch check

for fit and glue in place.

Put in place the canopy over the fuselage

hatch.

Glue in place.

Slide the wing tube into one of the wing

halves.

Slide the tube thru the fuselage.

Slide the second wing half onto the wing tube

comming out of the fuselage side.

Push the two wing halves together till they ar

tight against the fuselage side.

Bolt the wing to the fuselage using a 1/4-20

nylon bolt.

Содержание Sukhoi ARF




















Результаты поиска

Содержание Sukhoi ARF

Отзывы:

Похожие инструкции для Sukhoi ARF

Бренды по названию

Популярные бренды

Carl Goldberg Products Sukhoi ARF, Инструкция по эксплуатации

Результаты поиска

Содержание Sukhoi ARF

Отзывы:

Похожие инструкции для Sukhoi ARF

Бренды по названию

Популярные бренды