Carel humiSonic UU02, Руководство пользователя, Страница: 39 / 68

7
ENG
Direct version for room applic. +0300062IE - rel. 1.1 - 16.11.2017
1. INTRODUCTION AND ASSEMBLY
1.1 humiSonic (UU0*R)
Range of ultrasonic adiabatic humidifiers for direct humidification in rooms,
with built-in fans for uniform atomised water distribution. humiSonic is
suitable for many applications, such as: the humidification in production
plants, datacenters, warehouses, printing facilities, museums, restoration
workshops, theatres, etc., where optimisation of room humidity is essential
in ensuring personal comfort and safeguarding goods.
1.2 Part numbers
P/N Description
UU0(X)R(*)0000 without auxiliary card, without humidity probe
UU0(X)R(*)AS00 with auxiliary card and with humidity probe
Tab. 1.a
(X) =
2 à
2 kg/h (4.4 lbs/h),
4 à
4 kg/h (8.8 lbs/h),
6 à
6 kg/h (13.2 lbs/h),
8
à 8 kg/h (17.6 lbs/h)
(*) =
D à
power supply 230 Vac,
1 à
power supply110 Vac
1.3 Dimensions and weights
317
274
A
Fig. 1.a
Models
UU02 UU04 UU06 UU08
Production kg/h (lbs/h) 2 (4.4) 4 (8.8) 6 (13.2) 8 (17.6)
Width A mm (in) 317 (12.5)
Height mm (in) 274 (10.8)
Depth mm (in) 483 (19) 608 (24) 733 (28.9) 858 (33.8)
Weight kg (lb)
packaged 11 (24.2) 14 (30.9) 17 (37.5) 21 (46.3)
empty 9,5 (20.9) 12,5 (27.6) 15,5 (34.2) 18,5 (40.8)
installed* 10,3 (22.7) 14,1 (31.1) 17,9 (39.5) 21,7 (47.8)
Tab. 1.b
* in operating conditions, filled with water.
1.4 Opening the packaging
□
Make sure the package is intact upon delivery and immediately notify
the transporter, in writing, of any damage that may be due to careless
or improper transport;
□
move the humidifier to the site of installation before removing from
the packaging, grasping the neck from underneath;
□
open the cardboard box, remove the protective material and remove
the humidifier,
□
the unit must be always stored in a dry place before installation.
1.5 Material supplied
Make sure the following are included:
1. wall-mounting bracket;
2.
kit of screws and anchors;
3. 1 cable gland;
4.
4 feet;
5.
user manual.
1.6 Preparing for assembly
•
The unit is designed to be assembled on a horizontal support or wall
that can support its weight in normal operating conditions (see par.
“Wall-mounting”);
•
Install the humidifier in a safe place where it cannot be tampered with,
as far as possible from any air flows;
•
Position the humidifier horizontally using a spirit level, observing the
minimum clearances in mm (see Fig. 1.b) to ensure the correct flow of
supply air and allow the required maintenance operations.
<0,5°
≥ 500
(19.7”)
≥ 450
(17.7”)
≥ 500
(19.7”)
≥ 200...300
(19.7”)
Fig. 1.b
Note : the minimum distance at the rear is recommended for
assembly on a horizontal support.
Important: for installation on a horizontal support/wall:
1. the humidifier takes in air through by the slits at the back/bottom
respectively;
2. the feet/spacers are fitted at the bottom/rear;
3.
the fill/drain hoses are attached at the rear/on the bottom;
4.
the power cable gland is fitted at the rear/on the bottom;
5. remove the rear bracket for assembly on a horizontal support.
ASSEMBLY ON A HORIZONTAL SUPPORT
1
1
2
2
3
4
AIR
Fig. 1.c
WALL-MOUNTING
2
2
1
4
3
AIR
AIR
1
Fig. 1.d
1.7 Wall-mounting
ATTENTION: mount the unit only to a masonry wall
.
Fit the humidifier to the wall using the support bracket already fixed to
the humidifier, and the kit of screws supplied (for the dimensions and
weights see the previous paragraph).