Carefree ALTITUDE Скачать руководство пользователя страница 12

Страница: 12 / 18

LTITUDE

Service

Manual

Carefree of Colorado

070026-301

ITCH

DJUST

SSEMBLY AND

ARTS

EPLACEMENT

This procedure describes the steps to replace the pitch adjust assembly, valco buttons and the arm rollers.

EPLACING THE

ALCO

UTTON

1. Extend the awning to access the inside of the pitch adjust assembly.

2. Adjust the awning pitch to the flat (minimum) pitch

3. Disconnect power to the awning.

4. Squeeze the old valco button and lift out.

5. Insert the new valco button. Ensure that the buttons are inside the lever

arms and engage the holes in the pitch adjust assy and the arm channel.

EPLACING THE

OLLERS OR

ITCH

DJUST

SSEMBLY

The following procedure is used to replace the arm rollers or the complete pitch adjust assy.

NOTICE

This procedure requires two people. The second person is required to hold support the

arm and roller tube during the procedure.

1. Extend the awning to access the

pitch adjust assy.

2. Disconnect power to the awning.

3. If installed, remove the optional

lower wire cover.

4. Drill out the rivet stop at the

bottom of the arm channel.

5. Have one person hold and lift

the arm and roller tube.

6. Press in the pitch adjustment

pins and slide the pitch adjust
assy out of the arm channel.

7. Slide the pitch adjustment assy

out of the bottom of the rear
channel.

8. For roller replacement, remove

the old rollers from the posts.

9. Slide the new rollers onto the

posts of the pitch adjust assy.

NOTE:

The rollers are shipped

loose with new pitch adjust assy.

10. Slide the pitch adjust assy and rollers into the rear channel. Note the orientation as shown.

11. Align the arm channel and pitch adjust assy and slide together. It will be necessary to press in the

valco buttons. Push the parts together until the valco buttons pop out of the standard adjust holes in
the channel.

12. Install a 1/8" pop rivet in the rivet stop hole that was drilled out previously.

Valco Button

View of Back Channel

Alt023

Optional
Wire Cover

Drill Out
Rivet Stop

Pitch Adjust
Assy

Rollers (x2)

Alt024

1/8" Pop Rivet

Содержание ALTITUDE



















Результаты поиска

Содержание ALTITUDE

Отзывы:

Бренды по названию

Популярные бренды

Carefree ALTITUDE, Руководство по обслуживанию

Результаты поиска

Содержание ALTITUDE

Отзывы:

Бренды по названию

Популярные бренды