7
|
PHONE CALLS
Answer a call
Tap
or speak any word loudly to answer by VOX
Reject a call
Remain silent for 15 seconds, or press
for 2 seconds
End a call
Tap
Voice Dial*
(if supported
by mobile phone)
Press for 2 seconds and follow the prompt from the
mobile
Redial*
Press for 2 seconds
Hot Dial**
Tap
three times
Set default mobile***
While on a phone call, press
for 5 seconds
Change default
mobile
In Standby, press
for 5 seconds
INTERCOM CONFERENCE MODE
Add/Remove Channel
“A” to/from a call
Tap
while on a phone call
Add/Remove Channel
“B” to/from a call
Double-tap
while on a phone call
*This feature is not available during intercom or mobile calls.
** Before using Hot-Dial, configure the number via the
Cardo Community
.
*** If 2 mobile phones are paired directly to your cardo SHO-1, set one to use as
default for outgoing calls.
8
|
A2DP MUSIC AND FM RADIO
Turn on A2DP Music
In standby, tap
Turn on Radio
In standby, double-tap
Pause / Stop Audio
Press
for 2 seconds
Next Track / Station
With music ON, tap
Previous Track /Station*
With music ON, double-tap
RDS On/Off
(Default: Off)
With Radio ON, press and simultaneously for
2 seconds
Music Sharing (via A2DP only)
[SENDER] Start/Stop
sharing your music
During A2DP music playback, press
for 2
seconds
[RECEIVER] Stop music
sharing
Press
for 2
seconds
*With some phones you may need to repeat this action
9
|
INTERCOM
Note:
cardo SHO-1 DUO units are already factory paired!
Pairing
Pairing with
a “One+8”
Intercom Buddy
• Pair via the
Cardo Community
or
• In Standby, press
for 5 secs. Purple LED = success
Pairing Intercom
Channel A
In Standby, press
for 5 seconds.
Channel
“A”
pairs automatically – Rapid RED flashing.
Pairing Intercom
Channel B
In Standby, press
for 5 seconds.
When LED begins flashing , tap
twice – Rapid BLUE flashing
3-Way Intercom
• Rider 1 and Rider 2 pair via
“A”
• Rider 1 and Rider 3 pair via
“B”
4-Way Intercom
• Rider 1 and Passenger 2 pair via
“A”
.
• Rider 3 and Passenger 4 pair via
“A”
• Passenger 2 and Passenger 4 pair via
“B”
Calling “One+8” Intercom Buddies
Voice Connect (VOX)
OR
Manual Mode
a. Speak any word loudly into the
microphone or tap
.
b. When you hear the Voice
Command tone, say the name
of the “One+8” Intercom
Buddy
a. Press
for 2 seconds
b. Hear the names of all paired Buddies.
c. Tap
or speak any word loudly into the
microphone when you hear the name.
To cancel “One+8” Buddy List playback:
Press
for 2 seconds.
Calling Intercom Channels “A” and “B” (Two and Three-Way Calls)
Voice Connect (VOX)
OR
Manual Mode
Speak any word loudly into the
microphone. When you hear the
Voice Command tone, say “Call
Intercom” to start an intercom
call with
“A”
and/or
“B”
(subject
to who is present)
VOX Intercom call with only
“A”
or
“B”
will end automatically
after 30 seconds of silence.
Use this to start an Intercom call with:
• Channel “A”: Tap
• Channel “B”: Double-tap
To end a call tap
.
If you are already in an Intercom call with
“A”
or
“B”,
you can add another rider (
“A”
or
“B”
) by tapping
, or another rider
can join the intercom call in the same way.
Three-Way Calls
Use Ch
annel
“B”
Use Chann
el “A”
Rider 2
Rider 3
Rider 1
Four-Way Calls
Calling
1. Make sure all four units are in Standby.
2. Passenger 2 should double-tap
to call Passenger 4.
Wait until audio is heard on both units.
3. Rider 1 should tap
to call Passenger 2.
4. Rider 3 should tap
to call Passenger 4.
10
|
CLICK TO LINK (“CTL”) CALLS
Start a CTL call request
(search lasts up to 10 sec.)
Tap
three times
End a CTL call /
Cancel a CTL call request
Tap
Accept a CTL call
When hearing the
CTL
ringtone:
Tap
or say any word loudly to answer by VOX
Reject a CTL call
While hearing the
CTL
ringtone:
Remain silent until the ring tone stops or press
for
2 seconds
Enable / Disable CTL
(Enabled by default)
Via the Settings Menu, the App or
Cardo Community
11
|
TROUBLESHOOTING
Reboot
If your cardo SHO-1 stops responding, reset it by turning it off and
then on again (press
for 2 seconds
)
.
Reset Pairing
(Deletes all
paired devices)
1. In Standby, press for 5 secs until LED flashes RED/BLUE.
2. Press
for 2 seconds until LED flashes 5 times in PURPLE.
The contents of this User Guide, including all text, illustrations and drawings are the exclusive intellectual
property of Cardo Systems, Inc. (the “Company”) and are protected by copyright laws. Any partial or total
reproduction, translation and or dissemination, without the prior written authorization by the Company are
strictly prohibited. Any rights not expressly granted herein are reserved.
M
AN
01
00
7 S
HO
-1 Q
G E
N J 0
06
www.cardosystems.com
USA & Canada: 1-800-488-0363; International: +49 89 450 36819
