Cardinal Health Alaris 8000 Series Скачать руководство пользователя страница 257

Страница: 257 / 378

Programming

4-13

Alaris

System Directions for Use

SpO

Modules Section

Channel Options

(Continued)

To change

Saturation Averaging Time

, press applicable

soft key. Selectable options are

and

seconds.

•

FAST SAT

is enabled when

seconds is selected.

To return

SPO2

Main

display, press

CONFIRM

soft key.

Increase

Decrease

Saturation Averaging

Time

4 Seconds

CONFIRM

>Press CONFIRM

with

Fast SAT

Changing Saturation Averaging Time

(Continued)

Changing Sensitivity Mode

Press

Sensitivity Mode

soft key.

Pulse Beep Volume: Off

Sat. Averaging Time: 8

Limit Mode:

Adult

Channel Options

>Select an Option or
EXIT

EXIT

Sensitivit

Mode:

Normal

To change

Sensitivity Mode

, press applicable soft key.

•

Normal

: Normal patient monitoring.

•

Maximum

: Improved low perfusion performance.

Normal

Maximum

Sensitivit

Mode

EXIT

>Select an Option or
EXIT

NOTE:

The sensitivity mode displays on the

SPO2

Main

display only

when

Maximum

is selected.

(8220)

Содержание Alaris 8000 Series



























































































































































































































































































































































































Результаты поиска

Содержание Alaris 8000 Series

Отзывы:

Похожие инструкции для Alaris 8000 Series

Бренды по названию

Популярные бренды

Cardinal Health Alaris 8000 Series, Инструкция по применению

Результаты поиска

Содержание Alaris 8000 Series

Отзывы:

Похожие инструкции для Alaris 8000 Series

Бренды по названию

Популярные бренды