background image

 
 
 
 
 

CarShow 

 

Copyright 2013 All Rights Reserved 

Multi-Media Navigation System Installation Guide 

 

Rev A 

 

 

Installation Guide 

 
 
 

             
 
 
 
 
 
 
 
 
 
 
 

                        NOTE: CarShow System is only compatible with vehicles equipped with Single-Disc SYNC systems 

 

  

NOTICE OF INTENDED INSTALLATION AND USE

 

 

THE AUXILIARY VIDEO DISPLAY IS DISABLED WHEN THE VEHICLE

’S PARKING BRAKE IS NOT 

ENGAGED 

 

THE INSTALLER OF THIS PRODUCT MUST INSURE THE VIDEO DISABLE CONNECTION IS 

WORKING PROPERLY PRIOR TO DELIVERY OF THE VEHICLE.   

 

IMPROPER INSTALLATION COULD DISTRACT THE DRIVER OR INTERFERE WITH SAFE OPERATION 

OF THE VEHICLE, WHICH COULD RESULT IN SERIOUS INJURY OR DEATH, AND COULD ALSO 

VIOLATE STATE AND/OR FEDERAL LAW.  

 

CARSHOW ELECTRONICS DISCLAIMS ANY LIABILITY FOR ANY BODILY INJURY OR PROPERTY 

DAMAGE THAT MAY RESULT FROM ANY IMPROPER OR UNINTENDED INSTALLATION AND/OR USE. 

 
 
 
 
 

 
 

 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

STOP 

Damage to the vehicle may occur 

Do not proceed until process has been completed 

 

CAUTION

 

CAUTION 

Process must be carefully observed in order to 

reduce the risk of damage to the accessory or 

vehicle

 

 
 
 

CRITICAL 

Process must be carefully observed in order to 

ensure a quality installation

 

 

TOOLS and EQUIPMENT 

Specific tools and equipment recommended for this 

process

 

 

SAFETY RISK 

Observe safe practices, this process can be 

dangerous and there is a risk of personal injury

 

 

TESTING and TROUBLESHOOTING 

Content specific testing and troubleshooting points  

 

  

CS

-M

UST10 

Ford M

us

ta

n

 

Содержание CS-MUST10 Ford Mustang
















Отзывы: