Instruction manual CM465
Please keep this instruction manual for future reference
33
EN 30
7. Once inserted, make sure the two red buttons have snapped back
out, otherwise the service door cannot be closed.
•
The two red buttons are correctly snapped out (A).
•
The two red buttons are not snapped out (B).
8. Replace the drip tray and waste coffee container.
9. Close the service door.
Notes
• If the brewing unit is not put in place correctly, the service door
cannot be closed.
• If it is diffi cult to insert the brewing unit, it must be made into the
right height (before inserting) by pressing the brewing unit fi rmly
together from top and bottom.
• If it is still diffi cult to insert the brewing unit:
•
Leave it out of the appliance, place the drip tray, close the
service door, switch the main switch on the back of the appliance
to ‘off’ and then to ‘on’ again.
•
Wait for all the lights to go off, then open the door, remove the
drip tray and replace the brewing unit.
•
Replace the drip tray, together with the grounds container.
•
Close the service door.
Cleaning the milk container
Always clean the tubes inside the milk container when you prepare milk.
If there is still milk in the container, do not leave it out of the refrigerator
for longer than strictly necessary. Clean the container each time you
prepare milk as described in the section “Making cappuccino”.
All components can be washed in a dishwasher, placing them in
the top basket of the dishwasher.
1. Turn the milk container lid clockwise then remove it.
2. Remove the milk spout (S) and intake tube (M).
MAINTENANCE
1 CAPPUCCINO
2 CAFFE
LATTE
S
M
A
B
CLEANING THE MILK CONTAINER
Always clean the tubes inside the milk container when you
prepare milk. If there is still milk in the container, do not leave
it out of the refrigerator for longer than strictly necessary.
Clean the container each time you prepare milk as described
in the section “Making cappuccino”.
All components can be washed in a dishwasher, placing
them in the top basket of the dishwasher.
1. Turn the milk container lid clockwise then remove it.
2. Remove the milk spout (S) and intake tube (M).
3. Remove the frothed milk regulator (F) by pulling it
outwards.
4. Wash all the components thoroughly with hot water
and mild washing-up liquid. Make sure there are no milk
residues left inside the holes (H) and the groove (G) on the
fi ne end of the frothed milk regulator (F).
5. Check that the intake tube and spout are not clogged with
milk residues.
6. Replace the frothed milk regulator, milk spout and intake
tube.
7. Replace the milk container lid.
CLEANING THE NOZZLES
Clean the nozzles on the milk container every time after
heating milk or making cappuccino. Otherwise, remains of
milk may set hard.
- Place a container under the milk dispenser pipe and press on
the CLEAN button (N3) on the milk container for at least 5
seconds. The display shows “CLEANING”!
Warning! Risk of scalding from steam and hot water
escaping from the milk dispenser pipe.
EN 31
3. Remove the frothed milk regulator (F) by pulling it outwards.
4. Wash all the components thoroughly with hot water and mild
washing-up liquid. Make sure there are no milk residues left inside
the holes (H) and the groove (G) on the fi ne end of the frothed milk
regulator (F).
5. Check that the intake tube and spout are not clogged with milk
residues.
6. Replace the frothed milk regulator, milk spout and intake tube.
7. Replace the milk container lid.
Cleaning the nozzles
Clean the nozzles on the milk container every time after heating milk or
making cappuccino. Otherwise, remains of milk may set hard.
• Place a container under the milk dispenser pipe and press on the
CLEAN button (N3) on the milk container for at least 5 seconds.
The display shows “CLEANING”!
Warning! Risk of scalding from steam and hot water escaping from the milk dispenser pipe.
MAINTENANCE
G
F
H
H
N3
EN 31
3. Remove the frothed milk regulator (F) by pulling it outwards.
4. Wash all the components thoroughly with hot water and mild
washing-up liquid. Make sure there are no milk residues left inside
the holes (H) and the groove (G) on the fi ne end of the frothed milk
regulator (F).
5. Check that the intake tube and spout are not clogged with milk
residues.
6. Replace the frothed milk regulator, milk spout and intake tube.
7. Replace the milk container lid.
Cleaning the nozzles
Clean the nozzles on the milk container every time after heating milk or
making cappuccino. Otherwise, remains of milk may set hard.
• Place a container under the milk dispenser pipe and press on the
CLEAN button (N3) on the milk container for at least 5 seconds.
The display shows “CLEANING”!
Warning! Risk of scalding from steam and hot water escaping from the milk dispenser pipe.
MAINTENANCE
G
F
H
H
N3
CM465 Coffee Machine Instruction manual.indd 33
17/08/2017 13:59