21
Instruction manual C2105SS
20
Please keep this instruction manual for future reference
Instruction manual C2105SS
Please keep this instruction manual for future reference
S I D E R AC K S A N D C ATA LY T I C L I N E R S
To install, align the 2 holes in the catalytic liners with the 2 steel clips in the side of the oven
cavity. Once aligned, attach side racks by pushing these onto the furthest steel clip and then
clicking the other end onto the closest steel clip.
This will secure the catalytic liners to the sides of the oven. To remove, unclip the side racks from
the side of the oven, and remove the catalytic liners.
Visit our Caple website to view a ‘How to video’ on this. www.caple.co.uk
Telescopic runners
To assemble the telescopic runners:
- Remove the side racks
- Choose which shelf to use with the telescopic runner. Pay attention to the
direction in which the runner is to be extracted, position joint ‘B’ and joint ‘C’
on the frame (see Fig.
1
).
- Secure the two side racks with the guide rails using the holes provided on the
oven walls (see Fig. 3).The holes for the left rack are situated at hole F1, F2 and
the right rack at hole D1, D2.
- Finally, re-fit the side rack
Fig.
1
Side racks and Catalytic liners
To install, align the 2 holes in the catalytic liners with the 2 steel clips in the side of
the oven cavity. Once aligned, attach side racks by pushing these onto the furthest
steel clip and then clicking the other end onto the closest steel clip.
This will secure the catalytic liners to the sides of the oven. To remove, unclip the side
racks from the side of the oven, and remove the catalytic liners.
Visit our Caple website to view a 'How to video' on this. www.caple.co.uk
Telescopic runners
To assemble the telescopic runners:
- Remove the side racks
- Choose which shelf to use with the telescopic runner. Pay attention to the
direction in which the runner is to be extracted, position joint ‘B’ and joint ‘C’
on the frame (see Fig.
1
).
- Secure the two side racks with the guide rails using the holes provided on the
oven walls (see Fig. 3).The holes for the left rack are situated at hole F1, F2 and
the right rack at hole D1, D2.
- Finally, re-fit the side rack
Fig.
1
Side racks and Catalytic liners
To install, align the 2 holes in the catalytic liners with the 2 steel clips in the side of
the oven cavity. Once aligned, attach side racks by pushing these onto the furthest
steel clip and then clicking the other end onto the closest steel clip.
This will secure the catalytic liners to the sides of the oven. To remove, unclip the side
racks from the side of the oven, and remove the catalytic liners.
Visit our Caple website to view a 'How to video' on this. www.caple.co.uk
U S I N G T H E R OT I S S E R I E
12
T
he
rotisserie
function
can be used in
a number of programmes on this oven
. After fitting the food on to the spit
(
S
)
,
block it with the two forks
(
F
)
. then proceed as follows:
-
Fit the knobs protection as shown in (fig. 6)
-
Position the spit support as shown in (fig. 6)
-
Fit the end of the spit into the motor M at the back of the oven.
-
Fit the support into the circular groove in the spit.
-
Unscrew and remove handle A.
-
Place the oven tray with a little water on the lowest shelf of the oven.
-
Partially close the oven door.
-
When the cooking time is up, screw the handle on the spit and remove everything from the oven. If necessary,
use an oven glove to avoid any burn
s.
Fig.6
A
Using the Rotisserie
Fig 6
The rotisserie function can be used in a number of programmes on this oven (see page 18.)
After fitting the food on to the spit (S), block it with the two forks (F). then proceed as follows:
»
Position the spit support as shown in (fig. 6)
»
Fit the end of the spit into the motor M at the back of the oven.
»
Fit the support into the circular groove in the spit.
»
Unscrew and remove handle A.
»
Place the oven tray with a little water on the lowest shelf of the oven.
»
Close the oven door.
»
When the cooking time is up, screw the handle on the spit and remove
everything from the oven. If necessary, use an oven glove to avoid any burns.
Fig 1.
Fig 2.
T E L E S C O P I C R U N N E R S
To assemble the telescopic runners:
»
Remove the side racks
»
Choose which shelf to use with the telescopic runner. Pay
attention to the direction in which the runner is to be extracted,
position joint ‘B’ and joint ‘C’ on the frame (see Fig.1).
»
Squeeze the bars together slightly and clip either end of the
telescopic runners onto the side racks.
»
Finally, re-fit the side racks as per below.
