manualshive.com logo in svg

Cape Dory 270, Руководство пользователя

Поделиться
Скачать
Cape Dory 270 Скачать руководство пользователя страница 52

 

xv. EXTERIOR MAINTENANCE 

 
The exterior of a yacht should be maintained with great pride for it 
displays the value you place in it.  With regular attention and proper 
use, the outside appearance of your yacht will remain like new. 
 

FIBERGLASS 

 
Fiberglass is one of the most maintenance-free materials utilized today 
in boat construction.  If given proper care and treatment, the gelcoat 
surface will look new for many years.  If not maintained, it will 
eventually turn to a dull, chalky textured appearance. 
 
We recommend that you wash the exterior fiberglass surfaces of your boat 
several times each season with a mild soap and plenty of warm fresh 
water then rinse liberally with fresh water.  After the boat has dried, 
use a good quality fiberglass cleaner in paste form; follow this process 
with a wax or polish prepared for marine use.  A fiberglass cleaner with 
a very gentle abrasive in it may help remove minor scratches and surface 
wear.  Be careful, as the continued use of cleaners containing abrasives 
will gradually erode the gelcoat surface.  Marine wax will fill small 
scratches and provide a glossy finish.  We suggest you use a wax that 
does not contain silicone as it gets into the gelcoat and is almost 
impossible to remove should you want to paint the boat at a later date. 
 
Stubborn stains may be removed with fiberglass cleaner in some 
instances.  More difficult stains may be worked out with judicious use 
of a very mild abrasive powder cleaner.  Stubborn tar and petroleum 
stains may be removed with careful application of acetone solvent.  
(Acetone is a powerful but EXTREMELY flammable solvent which is 
available in most paint and hardware stores.) 
 
Stress or "spider cracks" are a common occurrence on the fiberglass 
boats of even the most careful boat builders and boat owners.  Most of 
the time, these cracks are limited to the gelcoat surface and are of 
cosmetic considerations only, not structural.  If you have any doubt 
about the seriousness of any crack, consult your dealer.  Cosmetic 
repair of gelcoated surfaces is not a difficult task and a reasonably 
handy person with a little practice and study can make adequate repairs.  
Structural fiberglass repairs should be left to experts. 
 
If for any reason you desire to apply paint to areas of the boat other 
than to the bottom or boot-top, seek the advice of qualified personnel 
at a boat yard in your area for information about the latest development 
in chemically-based paints for fiberglass, and the recommended surface 
preparation procedure. 
 
Minor repairs of the gelcoat surfaces may be done by the owner using one 
of the following methods: 

 

SURFACE IMPERFECTIONS:

  On imperfections that do not penetrate the 

gelcoat, you may sand them out with #320 wet and dry sandpaper.  Finish 
with 400 and 600 grit paper and hand buff with a fine rubbing compound. 

www.capedory.org 

- 52 -

 

Содержание 270































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды