CanyCom S25A Скачать руководство пользователя

Страница: 73 / 81

Troubleshooting

-64-

Troubleshooting

• If any malfunction or abnormal condition is found, immediately stop using the

machine and take an appropriate measure according to the Troubleshooting chart
below. If the malfunction or abnormal condition is not listed in the chart, or the
suggested measure does not solve the problem, consult with your CANYCOM
representative.

• Some corrective measures listed below require special knowledge and/or

equipment. Please contact your CANYCOM representative in such a case.

Area

Malfunction

Possible Cause

Corrective Measure

Ref.

Engine

Engine does not start,
or is difficult to start

Out of fuel.

→Fill fuel.

Page 19

Air in fuel system.

→Bleed air.

Page 48

Water in fuel.

→Drain water.

Page 48

Battery is discharged.

→Add battery fluid.
→Charge battery.
→Replace battery.

Page 58

Battery cable is
disconnected.

→Connect battery

cable.

Bad connection or
breakage in the wiring.

→Please contact

your CANYCOM
representative.

Starter switch, relay or
motor is defective.

→Please contact

your CANYCOM
representative.

Insufficient or wrong
oil.

→Fill or change oil.

Page 42

Other (other than the
above).

→Please contact

your CANYCOM
representative.

Engine stalls

Out of fuel.

→Fill fuel.

Page 19

Air in fuel system.

→Bleed air.

Page 48

Cold engine.

→Warm up engine.

Other (other than the
above).

→Please contact

your CANYCOM
representative.

Содержание S25A


















































































Результаты поиска

Содержание S25A

Отзывы:

Похожие инструкции для S25A

Бренды по названию

Популярные бренды

CanyCom S25A, Руководство оператора

Результаты поиска

Содержание S25A

Отзывы:

Похожие инструкции для S25A

Бренды по названию

Популярные бренды