Important
• The power supply should be within the following voltage range:
24 V AC: Voltage fluctuation within ±10% of 24 V AC (50 Hz or 60 Hz ±0.5 Hz or less)
Current supply capacity of at least 1.0 A per camera
12 V DC: Voltage fluctuation within ±10% of 12 V DC
Current supply capacity of at least 1.5 A per camera
• When using a 12 V DC battery power supply, be sure to connect resistors of at least 0.5 – 1.0
Ω
/20 W in
series to the power line.
• For an external power supply, use a double-insulated device.
Recommended Power Cables [Reference]
Cable (AWG)
24
22
20
18
16
12 V DC maximum cable length m (ft.)
5 (16.4)
9 (29.5)
14 (45.9)
23 (75.5)
32 (105.0)
24 V AC maximum cable length m (ft.)
11 (36.1)
18 (59.1)
29 (95.1)
46 (150.9)
64 (210.0)
Use UL cable (UL-1015 or equivalent) for 12 V DC or 24 V AC wiring.
AC Adapter
Please use the dedicated AC adapter (sold separately).
1
Remove the power connector attached to the AC adapter, then connect the multi-cable
included in the package, as shown in the following diagram.
1
Remove the power connector attached to the AC adapter, then connect the power interface
cable included in the package, as shown in the following diagram.
Multi-Cable or Power Interface Cable
AC Adapter
White
Blue (fat)
Brown (fat)
Green (fat)
Black
Insulate
External Device I/O Terminals
External device I/O terminals consist of two input and output systems each. Viewer can be
used to check external device input status and control output to an external device (please
refer to the “Operation Guide”).
2
Use the included multi-cable to connect to external device input/output terminals.
1: BROWN External device input 1 IN1 (+)
2: RED
External device input 2 IN2 (+)
3: BLACK External device input 1, 2 IN1 (-), IN2 (-)
4: ORANGE External device output 1 OUT1A
5: YELLOW External device output 1 OUT1B
6: GREEN External device output 2 OUT2A
7: BLUE
External device output 2 OUT2B
2
Use the included I/O interface cable to connect to external device input/output terminals.
1: BROWN External device input 1 IN1 (+)
2: BLACK
External device input 1 IN1 (-)
3: RED
External device input 2 IN2 (+)
4: BLACK
External device input 2 IN2 (-)
5: ORANGE External device output 1 OUT1
6: YELLOW External device output 1 OUT1
7: GREEN External device output 2 OUT2
8: BLUE
External device output 2 OUT2
External Device Input Terminals (IN1, IN2)
External device input terminals consist of two sets (IN1, IN2) of two terminals, with the negative
terminals connected to the camera interior GND. Connecting 2-wire cable to the positive and
negative terminals and opening or closing the circuit notifies the Viewer.
Important
When connecting sensors and switches, connect terminals that are electrically isolated from the
respective power and GND.
External Device Output Terminals (OUT1, OUT2)
External device output terminals consist of two sets (OUT1, OUT2) of two terminals. The sets
have no polarity. Controls from the Viewer can be used to open and close the circuit between the
terminals. Using optical couplers, the output terminals are isolated from the camera’s internal circuit.
Internal Connection Diagram
Internal controller
External device Input terminal
IN1, IN2
Output terminal
OUT1, OUT2
+3.3 V
0.1 µF
10 k
Ω
10 k
Ω
1 k
Ω
External device
The load connected to the output terminals
should be within the following rating range.
Rating between output terminals:
Maximum voltage 50 V DC
Continuous load current at or below 100 mA
On resistance: Max. 30
Ω
Audio Input/Output Terminals
Each audio input/output terminal has one input system and one output system.
Connecting the camera to an audio input/output device such as a microphone or a speaker
with an amplifier allows you to send/receive audio through the Viewer.
Use the 3.5 mm ( 0.14 in.) monaural mini-jack connector to connect to an audio input/output device.
3
Use the included multi-cable to connect audio input/output devices to the camera.
Use the 3.5 mm ( 0.14 in.) monaural mini-jack connector to connect to an audio input/output
device with the multi-cable.
Audio Input Terminal Common LINE IN/MIC IN (monaural input)
Although the camera has a single audio input system, it supports two types of microphone
input: LINE IN and MIC IN. Before using the audio input, please confirm the [Audio Input] in the
Setting Page (please refer to the “Operation Guide”). LINE IN is selected by default.
Input terminal: 3.5 mm ( 0.14 in.) mini jack (monaural)
• Dynamic MIC IN
Input impedance: 1.5 k
Ω
±5% * Supported microphones: Output impedance: 400 – 600
Ω
• Condenser MIC IN
Input impedance (microphone bias resistance): 2.2 k
Ω
±5%
Microphone power supply: plug-in power (voltage: 2.3 V)
* Supported microphones: Condenser microphones with plug-in power support
• LINE IN
Input level: Max. 1 Vp-p
* Use a microphone with an amplifier.
Audio Output Terminal LINE OUT (monaural output)
Connect the camera to a speaker with an amplifier. Audio can be sent to the speaker from the Viewer.
Output terminal: 3.5 mm ( 0.14 in.) mini jack (monaural)
Output level: Max. 1 Vp-p
* Use a speaker with an amplifier.
Specifications
Please refer to the “Appendix – Specifications” for specifications not listed below.
Pan Angle Range
348° ( ± 174°)
344° (-217° – +127°)
344° (± 172°)
Tilt Angle Range*
1
90°
93° (-3° – +90°)
Rotation Angle Range
360° ( ± 180°)
344° (± 172°)
Operating Environment
Temperature: Operating Temperature Range (including direct sun exposure)
AC, PoE+: -50°C – +55°C (-58°F – +131°F) DC, PoE: -10°C – +55°C (+14°F – +131°F)
Start-up Temperature Range (including direct sun exposure)
AC, PoE+: -30°C – +55°C (-22°F – +131°F) DC, PoE: -10°C – +55°C (+14°F – +131°F)
Humidity: 5% – 85% (without condensation)
Temperature: Operating Temperature Range (including direct sun exposure)
PoE: -10°C – +55°C (+14°F – +131°F)
Start-up Temperature Range (including direct sun exposure)
PoE: -10°C – +55°C (+14°F – +131°F)
Humidity: 5% – 85% (without condensation)
Temperature: Operating Temperature Range (including direct sun exposure)
PoE: -10°C – +55°C (+14°F – +131°F)
Humidity: 5% – 85% (without condensation)
Dimensions
(H x W x D) 111 x 102 x 252 mm (Main body only) (4.37 x 4.02 x 9.92 in.)
– Total length with the joint extended (D) : 455 mm (17.91 in.)
(H x W x D) 111 x 102 x 214 mm (Main body only) (4.37 x 4.02 x 8.43 in.)
– Total length with the joint extended (D) : 402 mm (15.83 in.)
(H x W x D) 111 x 102 x 214 mm (Main body only) (4.37 x 4.02 x 8.43 in.)
– Total length with the joint extended (D) : 384 mm (15.12 in.)
Weight
Approx. 3420 g (7.54 lb.)
Approx. 3360 g (7.41 lb.)
Approx. 2550 g (5.63 lb.)
Approx. 2120 g (4.68 lb.)
Approx. 2040 g (4.50 lb.)
Weather shield
Approx. 90 g (3.2 oz.)
*
1
Camera is at 0° when attached to the ceiling and facing straight down, and 90° when at a horizontal position.
Connecting the Camera
Included Cable
Multi-Cable
When using a multi-cable, refer to mark in the Installation Guide [2/2].
Please connect all of the connectors to the camera, even if you do not plan to use the external
power supply or the external device/audio I/O.
GND
1
3
1
7
3
2
1
OUT (White)
IN (Black)
Camera side
Power Interface Cable
1
3
1
I/O
Interface Cable
1
8
2
Power Connection
Please be sure to read the user manual for the dedicated power supply before use.
Note
• Power supply should conform to all local codes.
• The power supply should also comply with IEC/UL60950-1 (SELV/LPS) standards.
PoE+
/PoE (Power over Ethernet)
Power can be supplied to the camera by using a LAN cable connected to a PoE+/PoE HUB that conforms
to the IEEE802.3at Type2 (PoE+)/Type1 (PoE) standard. Use a category 5 or better LAN cable, 100 m (328
ft.) or less in length.
Important
• Check with your dealer for more information about PoE+/PoE HUB and Midspan technology.
Midspan (a LAN cable power supply device) is a device that, like a PoE+/PoE HUB, supplies power
to the camera via a LAN cable.
• Some PoE+/PoE HUBs allow the limitation of power for each port, but applying limits may interfere
with performance. If using this type of PoE+/PoE HUB, do not limit the operating power.
• Some PoE+/PoE HUBs have limits for the total power consumption for the ports, which can interfere
with performance when multiple ports are in use. In such a case, check the user manual for your
PoE+/PoE HUB.
•
When the camera is connected to both a PoE+/PoE HUB and an external
power supply (12 V DC or 24 V AC), power will be supplied in the following order of precedence.
External power supply (24 V AC) > PoE+/PoE HUB > External power supply (12 V DC)
However, when connecting power from both, certain combinations could cause problems such as
unstable network connections. If a problem arises, disable one of the power supplies.
External Power Supply
12 V DC or 24 V AC input can be used. 12 V DC can be connected in a non-polar configuration.
1
Use the included multi-cable to connect to the camera power connection terminal.
1: BLUE (fat)
24 V AC/12 V DC non-polar
2: BROWN (fat)
24 V AC/12 V DC non-polar
3: GREEN (fat)
FG (frame ground)
1
Use the included power interface cable to connect to the camera power connection terminal.
1: BROWN (fat)
24 V AC/12 V DC non-polar
2: BLUE (fat)
24 V AC/12 V DC non-polar
3: GREEN (fat)
FG (frame ground)
© CANON INC. 2019
Printed in Japan
