Canon PIXMA MP810, Руководство по обслуживанию, Страница: 11 / 20

* Before replacement of the logic board ass'y, check the ink absorber counter value (by service test print or EEPROM information print). If the counter value
is 7% or more, also replace the ink absorber kit when replacing the logic board ass'y. If the counter value is less than 7%, register the current ink absorber
counter value to the replaced new logic board instead.
[See 3-3. Adjustment / Settings, (6) Service mode, for details.]
2-3. Other Error Messages
ASF after an error occurred in the ASF cam
sensor. - ASF_PE sensor board
- Logic board
*
6 times Internal temperature error [5400] The internal temperature is not normal.
- Logic board
*
7 times Ink absorber full [5B00,
5B01] The ink absorber is supposed to be full.
Message on the LCD:
Ink absorber full. Service required.
Error codes:
5B00: Main ink absorber is full (overseas).
5B01: Main ink absorber is full (Japan).
- Ink absorber kit
8 times Print head temperature rise
error [5200] The print head temperature exceeded the specified
value. - Print head
- Logic board
*
9 times EEPROM error [6800] A problem occurred in writing to the EEPROM.
- Logic board
*
10 times VH monitor error [B200] The internal temperature exceeded the specified
value. - Print head
- Carriage unit
- Logic board
*
11 times Carriage lift mechanism error [5110] The carriage did not move up or down properly. - Sheet feed unit
- PR lift shaft ass'y
- Carriage lift sensor unit
- Logic board
*
12 times AP position error [6A00] An error occurred in the AP motor during purging
operation. - Sheet feed unit
- Purge unit
- Logic board
*
13 times Paper feed position error [6B00] An error occurred in the paper feed motor. - Sheet feed unit
- Logic board
*
14 times Paper feed cam sensor error [6B10] An error occurred in the paper feed cam sensor
during paper feeding from the front paper feed
cassette. - Sheet feed unit
- Logic board
*
15 times USB Host VBUS overcurrent [9000] The USB Host VBUS is overloaded.
- Logic board
*
16 times Pump roller sensor error [5C20] The pump roller position cannot be detected. - Purge unit
- Logic board
*
17 times Paper eject encoder error [6010] An error occurred in the paper eject encoder
signal. - Platen unit
- Timing sensor unit
- Timing slit disk eject film
- Paper feed motor
- Logic board
*
19 times Ink tank position sensor error [6502] None of the ink tank position is detected. - Platen unit
- Logic board
*
20 times Other hardware error [6500] The PCI bus error is detected by the ASIC.
- Logic board
*
22 times Scanner home position error [5010] The scanner unit cannot detect the home position,
or the scanner unit warming-up is not performed
properly at power-on.
On the LCD, "Scanner is not operating correctly."
is displayed. - Scanner unit
Power LED turned
off, and Alarm
LED lit ROM / RAM error The check sum value is incorrect in the ROM
check or RAM check at hard-power-on.
- Logic board
*
Message on the LCD Cause Solution
The selected paper cannot be fed from
cassette. Change the paper source and press
[OK]. The paper type being used (business card, Credit Card
size paper, or stickers, etc.) is not supported for paper
feeding from the cassette. Change the paper source to the ASF.
Cannot specify the followings together.
Change one of the settings. Settings made conflict each other. Change the paper type to other than plain paper for
borderless printing, or change to bordered printing
with plain paper.
Device memory is full. Reduce the amount of
photos, films, copies to scan. The memory is not sufficient to do the print job. Reduce the amount of data to be printed, or print from
a computer.
1-6