Canon PIXMA MP810, Руководство по обслуживанию, Страница: 10 / 20

2-2. Service Call Errors (by Cyclic Blinking of Alarm and Power LEDs)
Service call errors are indicated by the number of cycles the Alarm and Power LEDs blink, and the corresponding error code is displayed on the LCD.
becomes almost full. 1701] for ink absorber replacement. Press [OK]
to continue printing. Adjustment / Settings, (6) Service mode. ]
Pressing the OK button will exit the error, and enable
printing without replacing the ink absorber. However, when
the ink absorber becomes full, no further printing can be
performed unless the applicable ink absorber is replaced.
The connected digital
camera or digital video
camera does not support
Camera Direct Printing. [2001] --- The device may be incompatible. Remove
the device and check the manual supplied
with the connected device. Remove the cable between the camera and the machine.
Automatic duplex printing
cannot be performed. [1310] --- This paper is not compatible with duplex
printing. Remove the paper and press
[OK]. The paper length is not supported for duplex printing.
Press the OK button to eject the paper being used at error
occurrence.
Data which was to be printed on the back side of paper at
error occurrence is skipped (not printed).
Failed in automatic print
head alignment. [2500] --- Auto head align has failed. Press [OK] and
repeat
operation. <See manual> Press the OK button to clear the error, then perform the
automatic print head again.
(In the MP810, use Matte Photo Paper MP-101.)
The remaining ink amount
unknown. [1683] U130 (Applicable ink tank icon)
The remaining level of the following ink
cannot be correctly detected. Replace the
ink tank.
An ink tank which has once been empty is installed. Replace
the applicable ink tank with a new one.Printing with a once-
empty ink tank can damage the machine.
To continue printing without replacing the ink tank(s), press
the Stop/Reset button for 5 sec. or longer to disable the
function to detect the remaining ink amount. After the
operation, it is recorded in the machine EEPROM that the
function to detect the remaining ink amount was disabled.
Ink tank not recognized. [1684] U140 The following ink tank cannot be
recognized.
(Applicable ink tank icon) A non-supported ink tank is installed (the ink tank LED is
turned off). Install the supported ink tanks.
Ink tank not recognized. [1410 to
1419]
U150 The following ink tank cannot be
recognized.
(Applicable ink tank icon)
A hardware error occurred in an ink tank (the ink tank LED is
turned off). Replace the ink tank(s).
No ink (no raw ink). [1688] U163 The following ink has run out. Replace the
ink tank.
(Applicable ink tank icon)
Replace the empty ink tank(s), and close the scanning unit
(printer cover).
Printing with an empty ink tank can damage the machine.
To continue printing without replacing the ink tank(s), press
the Stop/Reset button for 5 sec. or longer to disable the
function to detect the remaining ink amount. After the
operation, it is recorded in the machine that the function to
detect the remaining ink amount was disabled.
Scanning unit (printer cover)
open. [1200] --- Cover is open. Close cover. Close the scanning unit (printer cover).
Scanner lock switch locked. [5020] --- Release the scanner lock switch and turn
the power off and back on. Unlock the scanner lock switch, turn the machine off, then
turn the machine on again.
Cycles of blinking
of Alarm and
Power LEDs
Error
Error
code
Conditions
Solution
(Replacement of listed parts, which
are likely to be faulty)
2 times Carriage error [5100] An error occurred in the carriage encoder signal. - Carriage unit
- Timing slit film
- Logic board
*
- Carriage motor
3 times Line feed error [6000] An error occurred in the LF encoder signal. - Timing sensor unit
- Timing slit disk film
- Feed roller
- Logic board
*
- Paper feed motor
4 times Purge cam sensor error [5C00] An error occurred in the purge unit. - Purge unit
- Logic board
*
5 times ASF (cam) sensor error [5700] This error takes place when feeding paper from the - Sheet feed unit
1-5