3
4
5
2
1
4
3
1
2
1
2
1
2
5
6
8
2
1
7
Realice la Alineación de los cabezales de impresión (Print Head Alignment).
Pulse el botón
REANUDAR/
CANCELAR (RESUME/CANCEL)
.
77
Cierre el soporte de la salida del
papel.
11
Cargue papel en el cassette como se describe en - hasta - .
Ajuste las guías del papel al tamaño del papel.
22
Cargue el papel MP-101
suministrado en el cassette.
33
Decida qué cassette utilizar en función del tamaño de papel.
Coloque el papel con la cara imprimible hacia abajo.
Antes de imprimir, cambie la configuración de la impresora para el tipo y el tamaño del soporte. Para
obtener más detalles, consulte el
Manual en pantalla
que se instalará posteriormente.
Tamaño de
papel y cara
imprimible
Extraiga el cassette (inferior).
11
Si la luz de
Alarma
(Alarm)
parpadea en
naranja, pulse el botón
REANUDAR/CANCELAR
(RESUME/CANCEL)
y
continúe con . Cuando
finalice la instalación,
consulte el
Manual en
pantalla
para repetir
la Alineación de los
cabezales de impresión
(Print Head Alignment).
Al cabo de 6 minutos, se imprime
un patrón en negro y azul. La
Alineación de los cabezales de
impresión (Print Head Alignment)
finaliza.
88
Ajuste la guía del papel derecha al
tamaño del papel.
Deslice el papel contra la guía
frontal.
44
Para obtener más información sobre el papel, consulte el
Manual en pantalla
que se instalará posteriormente.
Ajuste la guía del papel frontal al tamaño A4.
Deslice la guía del papel derecha hacia el lado.
Las guías del papel izquierda y derecha se mueven al mismo tiempo.
22
Deslice el cassette (inferior) hacia
atrás.
55
Pulse el botón Abrir.
Extraiga el soporte de la salida del
papel.
66
Si el punto de acceso que está utilizando dispone de un botón WPS, utilice ese botón para conectar la
impresora a la LAN inalámbrica.
Perform the Print Head Alignment.
Pull out the Cassette (Lower).
11
Press the
RESUME/CANCEL
button.
77
In about 6 minutes, a blue-black
pattern is printed. Print Head
Alignment is complete.
88
Close the Paper Output Support.
11
Load paper into the Cassette as described in - through - .
Adjust the Paper Guides to fit the paper size.
22
Load the supplied MP-101 paper
into the Cassette.
33
Adjust the right guide to fit the
paper size.
Slide the paper against the front
guide.
44
For information about paper, refer to the
On-screen Manual
which will be installed later.
Decide which Cassette to use according to the paper size.
Set the paper with the printable side down.
Before printing, change the printer settings for media type and size.
For details, refer to the
On-screen Manual
which will be installed
later.
Paper Size
and Printing
Side
If the
Alarm
lamp
flashes orange, press
the
RESUME/CANCEL
button, then proceed to
. After installation is
complete, refer to the
On-
screen Manual
to redo
Print Head Alignment.
Adjust the front Paper Guide to A4 size.
Slide the right Paper Guide to the side.
The left and right Paper Guide move together.
22
Slide the Cassette (Lower) back.
55
Press the Open Button.
Pull out the Paper Output Support.
66
If the access point that you are using has a WPS button, use that button to connect the printer to the wireless
LAN.