Canon Paper Deck Unit-F1 Скачать руководство пользователя страница 48

Страница: 48 / 112

Main Units

Removing the Pickup

Assembly

■ Preparation

1. Open the Compartment.

“Opening the

Compartment ” on page 43

2. Remove the Left Upper Cover.

“Removing the Left

Upper Cover” on page 36

■ Procedure

1. Remove the Connector Holder[1].

• 1 Screw[2]
• 3 Connectors[3]

[2]

[3]

[1]

2. Remove the Pickup Assembly[2] while releasing the

Coupling[1] toward the direction of the arrow.

• 4 Screws[3]

CAUTION:

Slide Guide (Upper) must be positioned as shown in
the figure when replacing the Pickup Assembly.

[1]

[2]

[3]

NOTE:

Release the Coupling when the Pickup Assembly is
installed.

CAUTION:

Be sure to keep opening the Compartment while
attaching the Pickup Assembly. It may cause not to
open the Compartment or damage the Pickup
Assembly with closing it.

■ Actions when Replacing the Parts

“Pickup Assembly ” on page 64

4. Disassembly/Assembly

Содержание Paper Deck Unit-F1
















































































































Результаты поиска

Содержание Paper Deck Unit-F1

Отзывы:

Похожие инструкции для Paper Deck Unit-F1

Бренды по названию

Популярные бренды

Canon Paper Deck Unit-F1, Руководство по обслуживанию

Результаты поиска

Содержание Paper Deck Unit-F1

Отзывы:

Похожие инструкции для Paper Deck Unit-F1

Бренды по названию

Популярные бренды