manualshive.com logo in svg

Canon MX883, Руководство по обслуживанию, Страница: 20 / 80

Поделиться
Скачать
Canon MX883 Скачать руководство пользователя страница 20

failed.

##281  TX

Re-transmission of the procedure signal has been 
attempted the specified number of times, but 
failed.

- Try a higher transmission level.  

##282  TX

Re-transmission of the procedure signal has been 
attempted the specified number of times, but 
failed.

- Try a higher transmission level.  

##283  TX

Re-transmission of the procedure signal has been 
attempted the specified number of times, but 
failed.

- Try a higher transmission level.  

##284  TX

After TCF transmission, DCN has been received. - Set the receiving machine ready for 

reception.  

##285  TX

After EOP transmission, DCN has been received. - Re-send the fax.  

##286  TX

After EOM transmission, DCN has been 
received.

- Re-send the fax.  

##287  TX

After MPS transmission, DCN has been received. - Re-send the fax.  

##288  TX

After EOP transmission, a signal other than PIN, 
PIP, MCF, RTP, RTN has been received.

    

##289  TX

After EOM transmission, a signal other than PIN, 
PIP, MCF, RTP, RTN has been received.

    

##290  TX

After MPS transmission, a signal other than PIN, 
PIP, MCF, RTP, RTN has been received.

    

##670  TX

In V.8 late start, the DIS V.8 ability from the 
receiving machine was detected, and CI was sent 
in response; however, the procedure failed, 
causing T1 time-over.

- In bit 0 of the service data #1 SSSW 

SW28, prohibit the V.8 / V.34 
procedure of the sending machine.  

##671  RX

In V.8 call reception, the procedure fails to 
proceed to phase 2 after CM detection, causing 
T1 time-over.

- In bit 0 of the service data #1 SSSW 

SW28, prohibit the V.8 / V.34 
procedure of the sending machine.  

##672  TX

In V.34 transmission, the procedure fails to 
proceed from phase 2 to phase 3 or later, causing 
T1 time-over

- In bit 0 of the service data #1 SSSW 

SW28, prohibit the V.8 / V.34 
procedure of the sending machine.  

##673  RX

In V.34 reception, the procedure fails to proceed 
from phase 2 to phase 3 or later, causing T1 time-
over

- In bit 0 of the service data #1 SSSW 

SW28, prohibit the V.8 / V.34 
procedure of the sending machine.  

##674  TX

In V.34 transmission, the procedure fails to 
proceed from phase 3 or 4 to the control channel 
or later, causing T1 time-over

- In bit 0 of the service data #1 SSSW 

SW28, prohibit the V.8 / V.34 
procedure of the sending machine.  

##675  RX

In V.34 reception, the procedure fails to proceed 
from phase 3 or 4 to the control channel or 
further, causing T1 time-over

- In bit 0 of the service data #1 SSSW 

SW28, prohibit the V.8 / V.34 
procedure of the sending machine.  

##750  TX

After transmitting PPS-NULL in ECM 

- Try a higher transmission level.  

15 / 76

Содержание MX883

















































































Отзывы:

Нет отзывов