Canon iPF720 - imagePROGRAF Color Inkjet Printer Скачать руководство пользователя | Manualshive

Страница: 72 / 204

background image

Chapter 2

2-16

2.3.2.2 Ink Tank Unit

2.3.2.2.1 Structure of Ink Tank Unit

0013-6934

a) Ink tanks

Each color-specific ink tank is filled with 130 mL of ink (90 mL for the starter ink tanks bundled with the printer). The ink level in each ink tank is memorized in
EEPROM attached to the tank and is detected as a dot count on the basis of the EEPROM information.
When an electrode attached to a hollow needle detects no continuity, it displays a message reporting that the ink tank is nearly empty. If the dot count reaches a
predesigned value in this state, an ink out condition is assumed.

b) Ink port

Depressing the ink tank fixer lever on the printer would cause would cause a hollow needle to pierce the ink port sealed by a rubber plug, linking the ink passage
of the ink tank to the printer.

c) Air passage

Depressing the ink tank fixer lever on the printer would cause an open hollow needle to pierce the air passage sealed by a rubber plug, releasing the internal pressure
of the ink tank to keep it constant.

d) Notches for preventing incorrect installation

Ink tanks are furnished with a notch for preventing incorrect installation. If the installation of an ink tank in incorrect position is attempted, the notch would interfere
with it, preventing its installation.

The ink tank fixer lever won't lower without the ink tank fully inserted to reach the mounting position, so the ink cannot be supplied.

e) Agitating plate

Assists in the agitation of pigment inks during ink agitation carried out to prevent their settlement.

F-2-9

EEPROM

Ink port

Ink tank

Air passage

Notches for preventing
incorrect installation

Agitation plate

Notches for preventing
incorrect installation

Notches for preventing
incorrect installation

«
...
70
71
72
73
74
...
»

Содержание iPF720 - imagePROGRAF Color Inkjet Printer













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для iPF720 - imagePROGRAF Color Inkjet Printer

Бренд: MIMAKI Страницы: 146

Бренд: MIMAKI Страницы: 180

RoboPro CE5000-40-CRP:

Бренд: CMi Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды