Canon imageRUNNER 2545, Руководство по обслуживанию

Страница: 199 / 362

7
7
7-5
7-5
Ecode Detail
Code
Item Description
E110 0002 Title Failure of the Scanner Motor (M21)
Description The speed lock signal indicates a deviation 10 times in
sequence at intervals of 100 msec after the signal has
indicated a locked state.
* The same condition is detected after the error retry is
performed.
Remedy 1.Check the cable.
2.Replace the Laser Scanner Unit.
3.Replace the DC Controller PCB (PCB4).
E110 0003 Title Failure of the Scanner Motor (M21)
Description The scanner motor (M21) speed lock signal does not indicate
a locked state for 6.5 sec. after a switchover is made from
low to normal speed or for 8 sec. after a switchover is made
from normal to low speed.
* The same condition is detected after the error retry is
performed.
Remedy 1.Check the cable.
2.Replace the Laser Scanner Unit.
3.Replace the DC Controller PCB (PCB4).
E196 0000 Title Error in EEPROM access
Description 20 retries failed after error occurred during communication
with EEPROM.
* Error occurs after the delivery if a paper in passage exists.
Remedy 1.Replace the DC Controller PCB (PCB4).
E197 0000 Title Error in communication of Laser Driver PCB (PCB14)
Description Communication error 1 with image PCB
Remedy 1.Check the cable.
2.Replace the Laser Scanner Unit.
3.Replace the DC Controller PCB (PCB4).
E197 0001 Title Error in communication of Laser Driver PCB (PCB14)
Description Communication error 2 with image PCB
Remedy 1.Check the cable.
2.Replace the Laser Scanner Unit.
3.Replace the DC Controller PCB (PCB4).
E202 0000 Title There is an error in the detection of the CCD home position.
Description 1.The attempt to detect the home position fails when the CCD
is moved forward.
2.The attempt to detect the home position fails when the CCD
is moved back.
Remedy 1.Disconnect and then connect the flexible cable(Relay PCB
(PCB2)-Main Controller PCB (PCB1) 64pin).
2.Replace the flexible cable.
3.Replace the CCD HP sensor (S22).
4.Replace the Scanner Motor (M21).
5.Replace the Relay PCB (PCB2).
6.Replace the Main Controller PCB (PCB1).
Ecode Detail
Code
Item Description
E225 0000 Title The light intensity of the CCD is faulty.
Description The light intensity of the CCD during shading is under the
specified level.
Remedy "1.Disconnect and then connect the flexible cable.
2.Replace the flexible cable.
3.Replace the CCD Unit.
4.Replace the Relay PCB (PCB2).
5.Replace the Main Controller PCB (PCB1)."
E227 0000 Title The reader unit power supply (24V) is faulty.
Description 1.At time of power-on, the 24V port is off.
2.At the start of a job, the 24V port is off.
3.At the end of a job, the 24V port is off.
4.When a load is being driven, the 24V port is off.
Remedy 1.Disconnect and then connect the power supply harness
connector.
2.Replace the Power Supply PCB (PCB3).
E240 0000 Title Error in controller communication
Description The serial communication error such as parity error or
overrun error is constantly detected.
Remedy 1.Check the Connectors.
2.Replace the DC Controller PCB (PCB4).
E240 0001 Title Error in controller communication
Description The serial communication error such as parity error or
overrun error is detected while printing.
Remedy 1.Check the Connectors.
2.Replace the DC Controller PCB (PCB4).
E248 0000 Title EEPROM error
Description 1.An error has occurred at power-on.
2.An error has occurred during write operation.
3.An error has occurred during read operation following write
operation.
Remedy 1.Disconnect and then connect the flexible cable(Relay PCB
(PCB2)-Main Controller PCB (PCB1) 50pin).
2.Disconnect and then connect the flexible cable(CCD unit-
Relay PCB (PCB2)).
3.Disconnect and then connect the power supply harness
connector.
4.Replace the flexible cable.
5.Replace the CCD Unit.
6.Replace the Relay PCB (PCB2).
7.Replace the Power Supply PCB (PCB3).
8.Replace the Main Controller PCB (PCB1).