Canon FAXPHONE L75 Скачать руководство пользователя | Manualshive

Страница: 128 / 183

background image

4-35

LASER CLASS 1060P Chapter 4: Maintenance & Service

3.3.4 Scanning problems

• Faulty scanning (Evaluation criteria: Test print is good, but the copied image is poor.)

• The document is not fed.

The document feed motor does not run. (Evaluation criteria: Check it visually.)

(1) Check the connection between the document feed motor and the PCNT board (J402).
(2) Check the document feed motor’s resistance. 13.95 ~ 25.68 W/1 phase is normal. (Fig. 4-4)
(3) Replace the document feed motor.
(4) Replace the PCNT board.
(5) Replace the SCNT board.

The document slips against the rollers. (Evaluation criteria: Check it visually. Stretched
copy image.)

(1) See page 4-4 and clean the document reading section.
(2) Replace the reading section’s rollers.

The document does not separate. (Evaluation criteria: Check it visually.)

(1) Check whether the document feed motor is driving all the rollers. (Check for any damaged gears or

foreign matter stuck inside.)

(2) Check whether the document feed lever is set to manual document feed.
(3) See page 4-4 and clean the separation roller and separation guide.
(4) Replace the separation roller and separation guide.

The scanner unit’s sensors are defective (Evaluation criteria: The placed document or
transported document is not detected.)

(1) Check for any faulty sensors while executing the copying operation and test mode.
(2) Check the connection between the OPCNT board (J2) and the SCNT board (J3).
(3) Replace OPCNT board.
(4) Replace the SCNT board.

«
...
126
127
128
129
130
...
»

Содержание FAXPHONE L75
























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FAXPHONE L75

Бренд: Unitech Страницы: 18

Бренд: Unitech Страницы: 26

Бренд: Panduit Страницы: 6

IMAGERUNNER ADVANCE C5051

Бренд: Canon Страницы: 72

iPF710 - imagePROGRAF Color Inkjet Printer

Бренд: Canon Страницы: 92

iPF8000S - imagePROGRAF Color Inkjet Printer

Бренд: Canon Страницы: 8

imageRUNNER ADVANCE C9075S PRO

Бренд: Canon Страницы: 48

IMAGERUNNER 7095 PRINTER

Бренд: Canon Страницы: 615

imageRUNNER C3125i

Бренд: Canon Страницы: 816

Бренд: Radio Shack Страницы: 57

Бренд: Oki Страницы: 45

Бренд: Samsung Страницы: 199

Бренд: idp Страницы: 104

Бренд: Lanier Страницы: 6

Бренд: Olympus Страницы: 28

Бренд: Oki Страницы: 192

Бренд: Oki Страницы: 48

WorkCentre 7200 series

Бренд: Xerox Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды