Canon DR-X10C - imageFORMULA - Document Scanner Скачать руководство пользователя

Страница: 31 / 160

Document Feeder Tray Extension

Extend as needed to match the length of the documents.

(See

p. 41.)

Rear View

USB Connector (Type B)

Connect the supplied USB cable here.

(See p. 14.)

SCSI Connector (50-pin half-pitch D-sub receptacle)

Connect the SCSI cable here.

(See p. 14.)

DIP Switch (SCSI ID)

Selects the scanner’s SCSI ID.

(See p. 15.)

Power Connector

Connect the supplied power cord here.

(See p. 14.)

Ventilation Holes (Exhaust Fan)

Exhausts heat from inside the scanner.

CAUTION

Do not block the ventilation holes. Doing so could cause the scanner
to overheat, creating a fire hazard.

Control Panel

Display Panel

Displays the user mode, job info, and messages.

Enter Key

Selects the user mode, and accepts settings.

Keys

Selects the user mode and job.

Menu Key

Displays the user mode.

Job Key

Displays jobs.

Содержание DR-X10C - imageFORMULA - Document Scanner

































































































































































Результаты поиска

Содержание DR-X10C - imageFORMULA - Document Scanner

Отзывы:

Похожие инструкции для DR-X10C - imageFORMULA - Document Scanner

Бренды по названию

Популярные бренды

Canon DR-X10C - imageFORMULA - Document Scanner, Руководство пользователя

Результаты поиска

Содержание DR-X10C - imageFORMULA - Document Scanner

Отзывы:

Похожие инструкции для DR-X10C - imageFORMULA - Document Scanner

Бренды по названию

Популярные бренды