background image

http://www.canon.com/c-park/

* Push and pull the lever on the 
   right. The barrels begin rolling 
   back and forth and merry 
   acrobat of clowns starts.

Assembly Instructions

Mountain fold(dotted line)

Make a mountain fold.

Valley fold(dashed and dotted line)

Make a valley fold.

Scissors line(solid line)

Cut along the line.

Cut in line(solid line)

Cut along the line.

 

Glue spot(Red dot)

Glue parts with the same number together.

Glue spot(Green dot)

Glue within the same part.

Glue spot(Blue dot)

Glue to the rear of the other part.

Glue

The glue spot(colored dot)
shows where to apply the glue.

Tools and materials

Assembly tip

Caution

Scissors, set square, glue(We recommend stick glue), pencil, used
ballpoint pen, toothpicks, tweezers, (useful for handling small parts)

Before gluing, crease the paper along mountain fold and valley 
fold lines and make sure rounded sections are nice and stiff.

Glue, scissors and other tools may be dangerous to young children 
so be sure to keep them out of the reach of young children.

View of completed model

Assembly Instructions : Twelve A4 sheets (No. 1 to No. 12)

*Hint: Trace along the folds with a ruler
  and an exhausted pen (no ink) to get a sharper, easier fold.

* Build the model by carefully reading the Assembly Instructions , in the parts sheet page order.

Before starting assembly : Writing the number of each section on 
its back side before cutting out the sections is highly recommended.
(* This way, you can be sure which section is which even after 
cutting out the sections.)

Indicates where sections should be glued together.

Indicates the order for assembling parts.

Indicates where to insert sections. 

Do not glue the sections together.

Round bar : Use to give parts a curved surface.

Tweezers : Useful in working with fine parts.

Be sure to build 
this model carefully.

Caution :

 Spread glue in a thin, 

              even layer before gluing 
              surfaces together.

Make two sets.

 (Moving) Clown in a barrel : Assembly Instructions

Содержание Creative Park Moving Clown in a barrel













Отзывы: