manualshive.com logo in svg

Canon Colorado 1630, Руководство по эксплуатации

Поделиться
Скачать
Canon Colorado 1630 Скачать руководство пользователя страница 133

Move media manually

Introduction

You can move media manually.

This gives you the option to move the media before and between jobs.

You can:
• Feed and retract media, see 

Feed and retract media manually on page 133

• Transport media by manual control, see 

Transport media by manual control on page 135

• Transport media by distance, see 

Transport media by distance on page 136

Feed and retract media manually

Introduction

You can feed the media to the platen or to the tape position, without sending a print job.

Feed weak media manually

When you feed the media manually, the printhead carriage will move over the media to scan the
side edges.

If the media you use requires a leading strip of rigid media then it is required to check the
[Requires Manual Loading] setting in the [Media Characteristics] section of the RIP software. With
this setting the scan will take place just before printing.

NOTE

The setting [Requires Manual Loading] only works when [Winding tension] is set to [Tension

bar] or [Locked tension bar].

Procedure

1.

Load the media. For more information see 

Prepare media for printing on page 82

.

2.

On the operator panel tap on the [Media] icon on the right.

3.

Tap on the arrow to select the roll you want to feed.

Move media manually

Chapter 4 - Handle the media

133

Содержание Colorado 1630





































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды