Canon AJ1 Скачать руководство пользователя страница 51

Страница: 51 / 56

6. Return the cassettes to their original positions.

NOTE:

If you are concerned with the difference in level of the cassettes after mechanical adjustment, adjust it by loosening the 2 screws.

7. Copy from the cassette, and check that the left edge margin is within 2.5mm +/- 1.5mm.

Cassette Left Edge Margin Adjustment (1st Side: Software

Adjustment)

Copy from the cassette, and check that the left edge margin is within 2.5 +/- 1.5mm (in the case of LTR/LGL: 4.2 +/- 1.5 mm).
When it is out of the specified range, perform the following procedure.

Feeding direction
of paper

image

1. Change the left edge margin adjustment value for the 1st side of the cassette.

• Service mode > COPIER > ADJUST > FEED-ADJ > ADJ-C1

When the value is increased by 1, the left edge margin is increased by 0.1 mm. (The image moves to the right.)

2. Copy from the cassette, and check that the left edge margin is within 2.5mm +/- 1.5mm.

5. Adjustment

Содержание AJ1

























































Результаты поиска

Содержание AJ1

Отзывы:

Похожие инструкции для AJ1

Бренды по названию

Популярные бренды

Canon AJ1, Руководство по обслуживанию

Результаты поиска

Содержание AJ1

Отзывы:

Похожие инструкции для AJ1

Бренды по названию

Популярные бренды