background image

Troubleshooting

Standard setup

The Target Access Point is Not Detected

Is the network device (router, etc.) turned on? If the network device is already turned on, turn it off, then turn it back 
on.
Check the access point name/network name and network password of your access point or router.
Are the computer and network device confi gured?
Are the access point and printer installed in an open space where wireless communications are possible?
Is the access point operating in IEEE802.11n (2.4 GHz), IEEE802.11g or IEEE802.11b?

After checking the above points, tap Search again on the printer to search for the access point again.

If the problem is not resolved, there may be other causes.

See also the sections below:

If SSID broadcast (connection via "ANY" SSID, etc.) is disabled or the stealth mode is enabled on the access point, 
enable SSID broadcast (connection via "ANY" SSID, etc.) or disable the stealth mode, then tap Search again on 
the printer to search for the access point again.
Select Directly enter the access point name in the Select access point screen. Wireless connection settings of the 
access point can be entered on the printer directly.
If "WPA/WPA2 Enterprise" is set as the security protocol (encryption standard) on the access point, change the 
security protocol (encryption standard) and confi gure wireless connection settings again. "WPA/WPA2 Enterprise" 
is not supported on this printer.
For details on how to change the security protocol (encryption standard) for the access point, refer to the manual 
supplied with the access point or contact its manufacturer.

Multiple access points with the same name exist. Do you want to use multiple access points?

The message appears when multiple access points with the same name are found.

When you have only one access point:
Select Use one AccessPoint only, then tap OK. Select the MAC address of the target access point on the displayed 
screen.

For details on how to check the MAC address of the access point, refer to the manual supplied with the access point 
or contact its manufacturer.




Содержание 6226B002


























Отзывы: