Canon 2417B002 Скачать руководство пользователя

Страница: 71 / 157

5-4

Chapter 5 Maintenance

Hint

An error message appears on the display panel if the upper unit
is open (raised).

Cleaning Rollers with a Cleaning Sheet

Rollers in the transport path are cleaned using the Cleaning
Mode of the User Mode, using a cleaning sheet.

Hint

• Each cleaning sheet is used several times to clean one side of the

rollers.

• Cleaning sheets can be purchased as consumables. For details,

contact your local authorized Canon dealer or service
representative.
Product Name: Cleaning Sheets (package of 30)
Product Code: 2418B002

■

Performing the Cleaning Mode

Use the following procedure to perform roller cleaning
using the Cleaning Mode.

Press the Menu key on the control panel.

The User Mode is activated.

Press the [

] key once to display “Cleaning Mode”.

Press [Enter].

The Cleaning Mode is enabled.

Press the [

] key to select [OK], and press [Enter].

The [Bypass Mode] key lights and the Document Feed
Tray rises as the scanner enters the waiting state.

Peel the liner from a cleaning sheet.

Menu Key

Enter Key

Bypass Mode Key

Содержание 2417B002






























































































































































Результаты поиска

Содержание 2417B002

Отзывы:

Похожие инструкции для 2417B002

Бренды по названию

Популярные бренды

Canon 2417B002, Руководство пользователя

Результаты поиска

Содержание 2417B002

Отзывы:

Похожие инструкции для 2417B002

Бренды по названию

Популярные бренды