Canon 2417B002 Скачать руководство пользователя | Manualshive

Страница: 4 / 157

background image

iii

Introduction

Thank you for purchasing the Canon imageFORMULA DR-X10C Document Scanner. Please read this and the following manuals
thoroughly before using the scanner to become acquainted with its capabilities and make the most of its many functions.
After reading the manuals, store them in a safe place for future reference.

Manuals for the Scanner

The documentation for the scanner consists of the

Easy Start

Guide

and the

Reference Guide

(supplied with the scanner),

the

User Manual

(this manual), and the

CapturePerfect3.0

Operation Guide

, which are provided in electronic form and

registered in the menu during software installation.

Easy Start Guide

This manual describes the procedures for setting up the
scanner for use. Please follow the procedures in the

Easy

Start Guide

to set up the scanner.

Reference Guide

This manual consists of the basic scanner operating
instructions extracted from the

User Manual

.

User Manual (This Manual)

This manual consists of two sections: Hardware and
Software.
The Hardware section provides general information about
the scanner operational settings, maintenance, and
troubleshooting.
The Software section describes how to use the ISIS/
TWAIN driver with the scanner, and how to set up job
registration tools.

CapturePerfect 3.0 Operation Guide
(Electronic Manual)

This is the operation guide for CapturePerfect 3.0, the
Canon document scanner application program.

Hint

• The User Manual and the CapturePerfect 3.0 document files

are installed in the following locations during software
installation.

User Manual

CapturePerfect 3.0 Operation Guide

«
...
2
3
4
5
6
...
»

Содержание 2417B002






























































































































































Отзывы:

Нет отзывов

Похожие инструкции для 2417B002

Бренд: Kogan Страницы: 3

Бренд: Leica Страницы: 144

Бренд: ION Страницы: 1

BCS 36 8ex Series

Бренд: Bartec Страницы: 12

Бренд: Xerox Страницы: 143

Бренд: Plustek Страницы: 2

Бренд: Radio Shack Страницы: 17

iNSIGHT 20 Plus

Бренд: Scantronic Страницы: 187

Бренд: Kogan Страницы: 12

Бренд: POSIFLEX Страницы: 24

Kiosk Full Page Reader PV35-00 Series

Бренд: 3M Страницы: 36

Input Scanner RS-232

Бренд: NCD Страницы: 7

Бренд: NCR Страницы: 217

Бренд: Epson Страницы: 21

Бренд: Epson Страницы: 13

B107011F - GT 10000

Бренд: Epson Страницы: 133

B11B181061 - GT 2500 Plus

Бренд: Epson Страницы: 28

ActionScanner ActionScanner II

Бренд: Epson Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды