background image

10

 

CAUTION: When using wire longer than that 
provided with your unit, follow the above chart. 
When running more than 30 feet from the 
battery, contact a qualified electrician. 

Powering Multiple Downriggers 

 

 

When operating multiple Mag 20 DTs, run a 

maximum of 2 downriggers per dedicated 
battery

. The advanced features of the Digi-Troll IV  

can keep the unit working virtually all the time. (See 
below for the recommended wiring setup.) 

 

NOTE: 

To ensure proper operation of your Digi-

Troll IV, ground its battery to your boat’s electrical 
system’s ground.  Malfunctions with the PIC, 
communication between units, or loss of operation 
result from faulty grounding.  Always check to see if 
your boat is properly grounded first. 

 

WIRI

NG

 YOUR 

DOWN

RIGGER 

Red  ( + ) 
 
Black  ( – ) 

Typical Operating Time*:

    

 

1 Mag 20 DT per battery –   24 hours. 

 

2 Mag 20 DTs per battery –  10 hours. 

 
*Time based on lab results using a 15lb weight 
and Deep-Cycle batteries. Actual run time will 
vary. 

FOR MAXIMUM PERFORMANCE:  

Use Minn Kota Group 27 or 31 sized, Deep-Cycle 
marine batteries. For extended battery life, add a 
Minn Kota on-board, DC alternator charger.  

 

Connect 
Multiple  
Batteries in 
Parallel 

AnglingOutpost.com

1-888-356-5022

AnglingOutpost.com

1-888-356-5022

Содержание Digi-Troll IV

























Отзывы: