Cannon CT-2000 Скачать руководство пользователя | Manualshive

Страница: 38 / 54

background image

30

CT-2000 Instruction Manual

Keypad Sequence

MENU

>

3

>

ENTER

>

2

>

ENTER

If the CT-2000 was previously configured to operate in a polled (RS-485) environment, the
Communication Mode message appears on the LCD as shown in Figure 26.

Figure 26: Communication Mode Display

The last line on the LCD indicates that timed reports are disabled and the present mode is polled.

In this example, the keypad sequence to press in order to operate in a point-to-point (RS-232)
environment with or without timed interval reports is:

2

>

ENTER

If the CT-2000 is configured to operate in a point-to-point (RS-232) environment, the
Communication Mode message appears on the LCD when the RS-232 option is enabled, as shown in
Figure 27.

Figure 27: Communication Mode Display

The last line on the LCD (3. Config Reports) indicates that timed reports may be utilized and the
present mode is point-to-point (2). In this example, the keypad sequence to reset the bath to a
polled environment is:

1

>

ENTER

Reports

The Reports option is accessed from the

MODE

sub-menu and is only enabled when the Point-to-

Point mode is selected.

«
...
36
37
38
39
40
...
»

Содержание CT-2000























































Отзывы:

Нет отзывов

Похожие инструкции для CT-2000

Бренд: Rath Страницы: 3

Бренд: dbx Страницы: 2

Бренд: idi Страницы: 20

Бренд: G&G Страницы: 2

Бренд: H&S Страницы: 46

Бренд: ParaBody Страницы: 3

Бренд: Hach Страницы: 52

Бренд: hager Страницы: 2

Бренд: VBM Страницы: 36

Бренд: W&H Med Страницы: 122

Бренд: Ultraflex Страницы: 3

Бренд: Maico Страницы: 55

Бренд: Maico Страницы: 38

Бренд: Maico Страницы: 2

Бренд: MAHA Maschinenbau Haldenwang Страницы: 13

ENET-232 Series

Бренд: National Instruments Страницы: 105

Бренд: Radial Engineering Страницы: 16

Бренд: R&S Страницы: 61

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды