Canmax CM-2D202 страница 222 Скачать руководство пользователя

Страница: 222 / 240

222

TROUBLESHOOTING

9-1 Repairs

Repairs and/or upgrades are not to be performed on this product.

These services are to be performed only by an authorized service center.

9-1-1 Inspecting Cords and Connectors

Inspect the scan engine’s interface cable and connector for wear or other signs

of damage. A badly worn cable or damaged connector may interfere with scan

engine operation. Contact your distributor for information about cable

replacement.

9-2 Troubleshooting

The scan engine automatically performs self-tests whenever you turn it on.

If your scan engine is not functioning properly, review the following

Troubleshooting Guide to try to isolate the problem.

Is the power on? Is the red or green aiming illumination line on?

If the aiming line doesn’t appear, check that:

• The cable is connected properly.

• The host system power is on (if external power isn’t used).

Is the scan engine having trouble reading your symbols?

If the scan engine isn’t reading symbols well, check that the symbols:

• Aren’t smeared, rough, scratched, or exhibiting voids.

• Aren’t coated with frost or water droplets on the surface

• Are enabled in the scan engine or in the decoder to which the scan engine

connects.

9-1 Repairs

9. MAINTENANCE AND

TROUBLESHOOTING

9-2 Troubleshooting

9-1-1 Inspecting Cords and Connectors

Содержание CM-2D202
















































































































































































































































Результаты поиска

Содержание CM-2D202

Отзывы:

Похожие инструкции для CM-2D202

Бренды по названию

Популярные бренды

Canmax CM-2D202, Руководство пользователя

Результаты поиска

Содержание CM-2D202

Отзывы:

Похожие инструкции для CM-2D202

Бренды по названию

Популярные бренды