Canmax CM-2D202 Скачать руководство пользователя страница 106

Страница: 106 / 240

106

SYMBOLOGIES

Not to Transmit

6-3-3 Codabar Check Character

Codabar check characters are created using different “modulos.” You can

program the scanner to read only Codabar barcodes with Modulo 16 check

characters.

Default = No Check Character

No Check Character

indicates that the scanner reads and transmits barcode

data with or without a check character.

When Check Character is set to

Validate and Transmit

, the scanner will only

read Codabar barcodes with a check character, and will transmit this character

at the end of the scanned data.

When Check Character is set to

Validate, but Not to Transmit

, the unit will

only read Codabar barcodes with a check character, but will not transmit the

check character with the scanned data.

No Check Character

Validate Modulo 16, but Not to Transmit

Validate Modulo 16 and Transmit

6-3-3 Codabar Check Character

Содержание CM-2D202
















































































































































































































































Результаты поиска

Содержание CM-2D202

Отзывы:

Canmax CM-2D202, Руководство пользователя, Страница: 106 / 240

Результаты поиска

Содержание CM-2D202

Отзывы: