04 GB
2.3. ADAPTING THE HOB TO DIFFERENT
TYPES OF GAS
To adapt the Hob for use with different types of gas, carry out the
following instructions:
•Remove the grids and burners
•Insert on hexagonal spanner (7 mm) into the burner support
(Figure
6)
•Unscrew the injector and replace it with one suitable for the gas to be
used
(see gas type table)
2.4. REGULATING THE MINIMUM FLAME
After lighting the burners, turn the control knob to the minimum setting
and then remove the knob (this can easily be removed by applying
gentle pressure).
Using a small «Terminal» type screwdriver the regulating screw can
be adjusted as in
Turning the screw clockwise reduces the
Figure .
8
gas flow, whilst turning it anticlockwise increases the flow – Use this
adjustment to obtain a flame of approximately 3 to 4 mm in length and
then replace the control knob.
When the gas supply available is LPG - the screw to set the idle flame
must be turned (clockwise) to the end stop.
When you have carried out the new gas regulation, replace the old gas
rating plate on your appliance with one (supplied with hob) suitable for
the type of gas for which it has been regulated.
3. USE OF HOB - USER INSTRUCTIONS
This appliance must only be used for the purpose for which it is
intended, domestic cooking, and any other use will be considered
improper and could therefore be dangerous. The Manufacturer will
not be responsible for any damage or loss resulting from improper
use.
Table A
Burner Type
Ø pan/pot
(cm)
AUX
SR
R
DC
kW
5
MONO
10 - 18
12 - 22
16 - 26
16 - 26
Auxiliary
Semi Rapid
Rapid
Power
(kW)
1,00
1,75
2,70
5,00 NG
4,6 LPG
G20/20 mbar
(methane)
95 l/h
167 l/h
257 l/h
476 l/h
G30/28-30 mbar
(LPG)
73 g/h
127 g/h
196 g/h
334 g/h
For smaller containers the gas burner should be regulated so that the
flame does not overlap the base of the pan. Vessels with a concave or
convex base should not be used.
WARNING: If a flame is accidentally extinguished, turn the knob
to the off position and do not attempt to re-ignite if for at least 1
minute.
If over the years the gas taps become stiff to turn it is necessary to
lubricate them.
Such operation must be carried out only by qualified Service
Engineers.
2)Tighten the joints with the spanner, remembering to twist the
pipes into position.
3)Attach fitting C to mains gas supply using rigid copper pipe or
flexible steel pipe.
IMPORTANT: carry out a final check for leaks on the pipe
connections using a soapy solution. NEVER USE A FLAME.
Also, make sure that the flexible pipe cannot come into contact
with a moving part of the cabinet (eg.adrawer) and that it is not
situated where it could be damaged.
Warning:
If gas can be smelt in the vicinity of this appliance turn off
the gas supply to the appliance and call the engineer directly. Do not
search for a leak with a naked flame.
Before using burner, be sure, grid perimeters center the burner as
below figure.
If you are using Cast Iron Grids; underneath the grid, position of it is
stated. Be sure for the exact grid is used in correct position.
3.1. USING THE GAS BURNER
GENERAL ADVISE
For best results, use cooking vessels with a flat surface. The size of
the surface should match the gas burner side as follows. Table A.
Prior to switching on the gas hob ensure that the burner caps are
correctly placed within their position. This hob is fitted with electronic
ignition to ignite the burner.
To ignite the burners carry out the following:
• Push in and turn anticlockwise to the larger flame symbol
or in
position
and keep pushed 5 seconds after ignition. The ignition
10
system will continue to generate sparks as long as the control knob is
being pressed Warning: If there is no electricity on appliance to ignite
the burner a match or a lighter should be used carrying out the out the
following:
• Place a lighted match or lighter close to the burner
• Push in and turn the knob anticlockwise to the larger flame symbol
or in position
and keep pushed 5 seconds after ignition Warning:
10
In any case if after 5 seconds the burner has not lit, stop operating the
device and wait at least 1 min before attempting a further ignition of the
burner.
KNOBS CONTROL
Each knob controls each burner as showed in the serigraphy. The
knobs have
steps from highest flame to lowest flame.
10
Never try to
switch from 0 to 1 (clockwise)
Indicateurs
Brûleur contrôlé par bouton contrôle
Brûleur éteint
Puissance la plus haute et allumage électrique
Puissance la plus basse
0
