C&K systems Sierra S5030 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 68

background image

6

Maintenance

47

Common System Messages

Below is an explanation of the common messages your keypad
might display. Beside each message is a discussion of what re-
sponses are appropriate. If you find the response is ineffective,
call your local C&K service representative.

You can get more than one error message at a time. For ex-
ample, you may note the Zone 3 LED is blinking slowly, the Zone
6 LED is steadily lit, and the Ready LED is unlit. This means that
Zone 3 is bypassed, Zone 6 is faulted, and the system is not
ready to arm.

If you notice:

That means:

What to do:

Power LED is off

Zone LED is on

Zone LED blinks
unevenly

Zone LED blinks
quickly (3 blinks in 2
seconds)

Zone LED
repeatedly blinks
quickly or unevenly

Ready LED is off

Zone LED blinks
slowly (2 blinks, 3
seconds)

The keypad is not
receiving power, or is
not functioning.

A zone is faulted;
system cannot fully
arm.

A sensor may need
service (trouble zone).

The sensor has been
tampered with, or has
signaled an alarm.

A sensor may need
service.

Any one of your
sensors may be
faulted.

The zone is bypassed.

Verify that the rest of the building is
receiving power; then call for service.

Correct the fault (by closing doors and
windows) or bypass the zone.

Bypass the sensor, or arrange for
repair.

Reset the system, as described in
Section 4. If LED continues to blink,
call for service.

Call for service.

Depending upon your arming type,
your system may be able to arm. If
not, correct any faulted zones and
then attempt to arm.

Remember the zone is unprotected.
You can remove the bypass (see
Section 3) or arm/disarm with bypass
in place.

Technical Manuals Online! - http://www.tech-man.com

«
...
49
50
51
52
53
...
»

Содержание Sierra S5030





































































Отзывы:

Нет отзывов

Похожие инструкции для Sierra S5030

Бренд: Rae Страницы: 49

Бренд: UbiBot Страницы: 11

Бренд: i3 International Страницы: 2

Бренд: i3 International Страницы: 2

Бренд: i3 International Страницы: 22

Бренд: 4xem Страницы: 68

Бренд: SGB Страницы: 49

Бренд: Watchguard Страницы: 4

Бренд: Panasonic Страницы: 16

Бренд: RAB Lighting Страницы: 9

Бренд: HuddleCamHD Страницы: 18

Elite RESPTZ37-1

Бренд: Revo Страницы: 65

Бренд: Europlex Страницы: 15

Бренд: Super Circuits Страницы: 28

Бренд: Malone Страницы: 19

Бренд: EAW Страницы: 2

Бренд: F&F Страницы: 8

Бренд: Avigilon Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды