manualshive.com logo in svg

C&H M 2 2 0, Руководство пользователя

Поделиться
Скачать
C&H M 2 2 0 Скачать руководство пользователя страница 14

 

 

8 

3.1.3

 

ID EEPROM 

 
The  EEPROM  holds  sixty-four  16-bit  words  of  M-Module  ID  data  and  VXI  M-Module  data.  
Refer Section 3.2.3 for more details. 
 
3.1.4

 

Row and Column Drivers 

 
The module uses a matrix drive scheme (rows and columns) in which a maximum of four of the 
relays  (one  row)  can  be  operated  at  any  one  time.   An on-board timer (part of Module Control 
block) ensures the relay coils have been driven long enough for the contacts to move and settle.  

The  Row  Driver  block  translates  the  ROW_SET(4:1)  and  ROW_RESET(4:1)  command  lines 
from  the  Module  Control  block  into  bipolar  and  tri-state  capable  buffered  drive  signals.    The 
ROW_DR(4:1)

 

signals provide either current source from the +5VDR supply (relay set), current 

sink to ground (relay reset), or tri-stated output (both current-source and current-sink off).  Each 
output is tri-stated whenever that particular row is not being driven.  

The Column Driver block translates the COL(4:1)

 

command lines from Module Control into the 

bipolar  buffered  drive  signals,  COL_DR(4:1).  The COL_DR(4:1) signals provide either current 
source from the +5VDR

 

supply (relay reset) or current sink to ground (relay set).  

3.1.5

 

Driver Power Switch 

 
This block removes all power from the Row and Column Driver circuitry except when needed to 
move relays.  This FET switch is open at power-up to prevent any relay contact movement until 
register writes cause drive-power to be applied.  

3.1.7  Relay Coils 
 
This block contains the 16 relay coils arranged as a 4x4 matrix.  To close a relay, a ROW_DR line 
sources current while a COL_DR line sinks current to ground.  To open a relay, a COL_DR line 
sources current while a ROW_DR line sinks current to ground.  Refer to Figure 3 for switching 
schematic.  

3.1.8  Reset and Power Conditioning 
 
This  block  filters  +5V  power  to  produce  VCC  power  (+5V)  for  logic  and  isolates  the  various 
grounds  used  by  the  module.    This  block  also  processes  the  /RESET  signal  from  the  Carrier 
Interface and monitors power to produce the /RST reset signal for the module.  

 

 

C&H Technologies, Inc. <> 445 Round Rock West Drive <> Round Rock, Texas  78681 <> www.chtech.com

Содержание M 2 2 0































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды